Question about Cars & Trucks

Open Question

I have a craftsman 3 ton floor jack and it will not go up

I called sears and they told me to check fluid level. I took out screw that had orange cap which said do not adjust.I did not see any other way to add fluid,I was not able to add much fluid at all. I am wondering what to do next?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: ttransmission fluid level check

The transmission is sealed, not meant to be maintained by consumer, supposedly "maintenance free."

Posted on Sep 24, 2008

  • 2920 Answers

SOURCE: Chevy Cavalier '98 Transmission has no dipstick - check level ?

take it to a shop and have them top it up so you can be sure you have the fluid you need to keep the car going as it should,,,,thats your safest bet

Posted on Dec 06, 2008

  • 45 Answers

SOURCE: how to add or check transmission oil

this t-bird has a 5r55s trans. it does not have a dipstick.
it has a "standpipe" type leveling system.
to check fluid level the tranmission has to be within 80-120 degree f.
take the plug out of the center of the fitting located on the bottom of the trans pan. it is a torx 30.
running in park the fluid should drip slower than a coffee pot.
to add you need a npt thread fitting the same as the little plug you removed. and attach a bottle of mercon5 and hose to it. squeeze the bottle to add fluid
then recheck it by letting it drain out to a fast dribble. then install the little plug back in.ead6e26.gif remember 80-120 degree fluid temp.

Posted on Feb 02, 2009

  • 1 Answer

SOURCE: checking transmission fluid level on 2005 c230 kompressor mb

what fluid did you want to check? oil, coolant, transmission, brake? let me know and maybe i can help. the leak you currently see what color is the fluid? black or dark brown probably enigne oil. red or dark brown probably some kind of hydraulic fluid--trans or brake, yellow, green or blue with a sickly sweet smell is probably coolant. i haven't worked on a c230 but as far as i know all transmissions have a dipstick where you can check the level. check your owner's manual. make sure the car is warmed up such as after a short drive to properly circulate and check the trans fluid. some cars also require the transmission to be placed in a specific position ie neutral when being checked. again check your owners manual.

to the guy that was critical about your question, i hope he stays as dumb and ignorant about his/her car as he seems as with his/her attitude--just keep bringing it to servcie, that way i can keep making a lot of money out of you. i actually prefer an owner who knows a litlte some thing about their car and how it works--it makes the job easier in communicating to me what may be wrong and thus i can save them time and money. we both win. just don't tell me what you think it is--just tell me the symptoms are, as a professional it's my job to figure it out from there. hope this helps.

Posted on Mar 14, 2009

  • 1 Answer

SOURCE: 2002 Toyota Echo Check Engine

You should get the problem code ran at a shop or auto parts store. My moms 2003 Toyota Echo check engine light came on and it had a slight misfire, I replaced all the sparkplugs about $20 and no check light.

Hope this was helpful

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do you put the transmission fluid?


There should be a dipstick, but some modenr transmissions are sealed and have no dipstick, and have a drain bolt instead.
LEVEL CHECK Inaccurate fluid level readings may result if the fluid is checked immediately after the vehicle has been operated under any or all of the following conditions:
  • In high ambient temperatures above 90°F (32°C).
  • At sustained high speeds.
  • In heavy city traffic during hot weather.
  • As a towing vehicle.
  • In commercial service (taxi or police use).
  • If the vehicle has been operated under these conditions, shut the engine OFF and allow the vehicle to cool for 30 minutes.
NOTE: The transaxle in your vehicle requires special procedures for checking and adding automatic transmission fluid. Fig. 1: Location of the fluid level screw and the fill/vent cap needed to check the fluid for the 4T40E automatic transaxle 87951085.gif
Fig. 2: The transaxle vent is also the transaxle fill cap 93201p22.jpg
Fig. 3: The vent cap is obstructed by the intake duct on the 3.1L engine. You will probably need to the remove the air intake duct 93201p30.jpg
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Place a container under the fluid level screw. Fig. 4: The fluid level screw (see arrow) is located above the transaxle pan on the passenger side of the vehicle 93201p42.jpg

  4. Remove the fluid level screw.
  5. Ensure the oil level is at the bottom of the level screw. NOTE: Because the transaxle operates correctly over a range of fluid levels, the fluid may or may not drain out of the screw hole after removing the screw. If the fluid drains through the screw hole the transaxle may have been overfilled. When the fluid stops draining the fluid level is correct, and you may install the level screw. If the fluid does not drain through the screw hole, the transaxle may have been low. Add fluid at the vent cap location in 1 pint ( 1?2 liter) increments until the oil level is at the bottom of the oil level hole. Use a long necked funnel to avoid spillage.
  6. Install the oil level screw and tighten to 124 inch lbs. (14 Nm).
  7. Lower the vehicle.
  8. Connect the negative battery cable.
prev.gif next.gif

Feb 12, 2011 | 1998 Chevrolet Malibu

3 Answers

Just got 1996 chevy cavalier. Where do you add transmission fluid?


the transmission fluid goes down the dip stick hole ,either use a small funnel or special tranny fluid refill top up bottle

Feb 04, 2011 | 1996 Chevrolet Cavalier

1 Answer

How to check trasmission fluid no dipstick just a red cap


4T40E Automatic Transaxle CAUTION
Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of the transaxle fluid to exhaust pipe. The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
  1. The fluid level should be checked when the transaxle is near room temperature or at 104°F (40°C). To acquire this, left the car idle for 3-5 minutes with all of the accessories off. Fig. 5: Location of the fluid level screw and the fill/vent cap needed to check the fluid for the 4T40E automatic transaxle 87951085.gif

  2. Apply the brake, then move the gear shift selector through all gear ranges, pausing three seconds in each range. Shift the lever into P.
  3. Raise and safely support the vehicle.
  4. Place a suitable drain pan under the check plug to catch any fluid that may drip out.
  5. Remove the oil check plug. The oil level should be at the bottom of the oil check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the screw hole when the screw is removed.
  6. If fluid drains through the screw hole, the transaxle may have been overfilled. When fluid stops draining, then fluid level is correct and the check plug may be installed. If fluid does not drain through the screw hole, the transaxle fluid may have been low. Add fluid at the vent cap location in 1 pint increments until the oil level is at the bottom of the oil check hole.
  7. Install the oil check plug/fluid level screw and tighten to 10 ft. lbs. (14 Nm).
  8. Carefully lower the vehicle.
prev.gif next.gif

Jan 21, 2011 | 1997 Pontiac Sunfire

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Need easy way to take off transmission fluid cap.Trying to check fluid.


Hello Eddie.

Checking the fluid level on these cars isn't easy. Not one of the Generals best ideas. There isn't a dipstick under that cap. The fluid level is checked by removing a screw on the side of the transmission while the car is running and sitting level.
This makes it tricky to do for the average do-it-yourselfer as you not only need to jack up the front of the car but the back end to keep it level. Probably a vain attempt to get the cars back into the dealers shop.

Anyway, here is the book procedure.

kiltylake_16.gif

kiltylake_17.gif


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect

The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  1. Install fluid level screw. Tighten 12 N.m (106 lb in)
  2. Lower vehicle.
I hope this helps you along.
Thank you for using FixYa.

KL

Nov 19, 2010 | 2000 Pontiac Grand Am GT

2 Answers

What tools do i need to change front brake pads


need a torque wrench, 3/8" drive 1/2" drive sockets, large screwdriver, screw in front caliper compressor, jack, jack stands, fluid catcher (pale), wrench set, etc.

Hope this helps.

Jul 13, 2010 | 2004 Kia Optima

1 Answer

No tranny dipstick to be found ANYWHERE!!!!!!!!!


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid. Inspect The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) . CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe. The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid. WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole. 1. Let vehicle idle for three to five minutes with accessories off. 2. Apply brake 3. Move shift lever through all gear ranges, pausing three seconds in each range. 4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist. 5. Raise vehicle on hoist. 6. Place oil container under fluid level screw. 7. Remove the fluid level screw with the engine running at idle. 8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID. 9. Install fluid level screw. Tighten 12 N.m (106 lb in) 10. Lower vehicle. 11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. 1. Install fluid level screw. Tighten 12 N.m (106 lb in) 2. Lower vehicle.

Jun 05, 2009 | 2004 Chevrolet Malibu

1 Answer

What Jack and stand to get for my '04 Ram 1500 Short Bed V6?


THE SAFEST CHOICE IS THE 3 TON.. YOU COULD GO WITH THE 2 OR 2.5 TON, BUT WITH THE SIZE OF YOUR TRUCK YOU NEED THE 3 TON..REMEBER TO ALWAYS USE THE JACK STANDS..GOOD LUCK KEITH...

Mar 14, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...