Question about Cars & Trucks

1 Answer

2004 gmc 2500 i have heated folding turn indicator side mirrors.turn indicator is not working on driver side.is it possible to repair ot do i need to replace?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,475 Answers

I'd call a GMC dealer and ask for the parts department. I'd ask about the availability and price of the driver's mirror turn signal bulb. That might tell you if that bulb is replaceable. You could also ask that same delaership's service department about the labor cost to replace the bulb.
If the plastic cover below the mirror will not snap off, you would probably have to remove the mirror from the door and take it apart to replace the bulb. Depending on the friendliness of the GMC service or parts department , they might tell you what to do here.

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: How to replace side mirror on 1996 GMC Sierra?

See Figure 2
0900c1528008f812.jpgFig. 2: Outside mirror-below eyeline type

  1. Remove the mirror cover screw and lift the cover and pivot the mirror towards the window.
  2. Remove the mirror to door bolts and remove the mirror and seal from the door.
  3. To install, position the mirror and seal to the door and install the retaining bolts.
  4. Pivot the mirror away from the window, and lower the mirror cover.
  5. Installation is the reverse of removal.
  Hope this helps .. if not feel free to contact me

Posted on Nov 12, 2008

  • 1214 Answers

SOURCE: need to replace passenger side view mirror 200 GMC Jimmy Diamond

On my '97, there was a triangular shaped piece of plastic on the inside trim that had to be removed. I think all three mounting screws were under that. It's been a few years, but I think that was how it was done.
I remember it was pretty easy though.

Posted on Jan 29, 2009

Blackberry_U
  • 223 Answers

SOURCE: Replacing only the driver side mirror w/o replacing the assembly.

You should be able to just replace the mirror as long as its flat.

Posted on Jun 15, 2009

  • 1 Answer

SOURCE: How to replace power, heated, folding door mirror

driver side power mirror won't move up or down. will move side two side.

Posted on Sep 29, 2009

autotherapis
  • 501 Answers

SOURCE: 2004 GMC Sierra 2500 HD. Drivers side mirror was

You should be able to replace the glass, but I believe it is glued in place. You should be able to tell as you remove the old pieces. It is a special white glue.
I was able to get a great price for the whole mirror on ebay. even the ones with signals and heated.

Hope this helps

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My motorised door mirror on my kia sorento 2004 cdi does not fold in ! I can hear the motor working in the mirror, I`m thinking the gearing is worn!


Hi,if you can hear the motor turning you are proberly right,you will have to open it up and have a look,good luck.

Jan 31, 2016 | 2004 Kia Sorento

Tip

On truck the 2004 GMC Truck Sierra you have on the dash a driver information...


Put the control (on the driver door for your side view mirrors) onto the passenger mirror position put the car in reverse, mirror tilts down and shows you the curb! (this only works on some models like the 3.0 not sure of what year of 1.8t)

on Mar 14, 2009 | 2006 Audi A4

1 Answer

2007 gmc heated mirror module


Could have a DDS an PDS .depends on what RPO code yours has >
Outside Mirror Description and Operation (with RPO DL3)
Or
Outside Mirror Description and Operation (without RPO DL3)
Without
Heated Outside Rearview Mirror Operation
The REAR DEFOG relay controls the operation of the heated outside rearview mirrors. When rear window defogging is requested, the REAR DEFOG relay is energized and B+ is applied to the supply voltage circuit of the mirror heater element, located in the mirror face. A constant ground is also applied to the mirror face. Current will pass through the mirror heater element, warming the mirror, so long as the rear window defogger is commanded ON.

With
Heated Outside Rearview Mirror
The DDS and PDS control the activation of the mirror heaters. Upon receiving a serial data message indicating a request for heated mirrors, the DDS and PDS, will apply voltage to the mirror heater element supply voltage circuit. The mirror heaters will remain active until a new message is received indicating rear defogger is to be deactivated.
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a four position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a three position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Mirror Extend/Retract Switch--Integrated into DDS and is a two position switch that allows the operator to select the mirror extend or mirror retract position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Folding Mirror Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Your best bet mite be to take to a qualified repair shop , i really don't think you'll be able to do anything with it.
Do you have wiring diagrams so you know which wires to test ,do you know how to do electrical testing ?
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.

Sep 15, 2017 | 2007 GMC Sierra 2500HD

1 Answer

2004 GMC Sierra 2500 HD. Drivers side mirror was


You should be able to replace the glass, but I believe it is glued in place. You should be able to tell as you remove the old pieces. It is a special white glue.
I was able to get a great price for the whole mirror on ebay. even the ones with signals and heated.

Hope this helps

Jan 09, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

2005 gmc sierra 2500hd heated seat turns off


you have a couple of problems first of all your drivers sd=ide heated heat pad is probably faulty, for your heating problem you may have to get the hvac doors recalibrated.

Oct 05, 2009 | 2004 GMC Sierra 2500

1 Answer

2003 gmc mirrors do not fold in


The power mirrors are controlled by a module (computer) DDM - drivers door module an the PDM - passenger door module .
Folding Mirror System
Folding Mirror System Controls
The folding mirror system requires signals from 2 separate switches. The mirror select switch must be in the neutral/fold position and the mirror direction switch must be activated to the left/extend or right/retract positions. Both switches are integrated into the DDM and provide direct signals.
Folding Mirror System Operation
Upon receipt of the required switch inputs the DDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function. The DDM will also send a class 2 message to the PDM indicating the requested function. The PDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function.

Power Mirror System
Power Mirror System Components
The power mirror system consists of the following components:
• The driver door module--Class 2 module with integrated switches and requires programming when replaced
• The passenger door module--Class 2 module with integrated switches, requires programming when replaced and also contains the RFA receiver
• The power mirror direction switch--Integrated into DDM and is a 4-position momentary switch that provides a signal input to the DDM for up, down, left/extend and right/retract with a mirror switch activation
• The mirror select switch--Integrated into DDM and is a 3-position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• The left outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The right outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The body control module--Class 2 module that requires programming when replaced, serves as the power mode master and is the main message handler
• The DDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The PDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The memory switch, if equipped with memory mirrors--Supplied power by the DDM and provides a voltage signal to the DDM upon a switch activation
• The horizontal and vertical position sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDM/PDM and provide a variable voltage signal to the DDM/PDM that is proportional to mirror position
• The park neutral position switch, if equipped with memory mirrors--Provides transmission gear selection information to the PCM and is used for memory recall and mirror tilt in reverse functions
• The powertrain control module, if equipped with memory mirrors--Class 2 module that requires programming when replaced and provides Class 2 message indicating transmission gear selection
• The driver information center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a Class 2 module that requires programming when replaced and is used to personalize the memory recall and mirror tilt in reverse functions
• Fold motor in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.
DTC B1722
The driver door module (DDM) and passenger door module (PDM) switch the mirror fold motor control circuits to battery voltage and ground in response to mirror extend or retract command.

Apr 06, 2017 | 2003 GMC Yukon XL

1 Answer

How to replace power, heated, folding door mirror on a 1999 GMC Suburban.


driver side power mirror won't move up or down. will move side two side.

Apr 09, 2009 | GMC K1500 Cars & Trucks

1 Answer

Does the passanger side heated mirror on a 2004 gmc yukon have a seperate fuse than the drivers side?Everything works except the heat.


some do some don't, check with the dealer parts dept for this info.Ask if u can buy just the mirror with heated glass elmement, I was able to do this on my Buick, cost was $60 US

Jan 14, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...