Question about 1985 Ford Bronco

1 Answer

Ignition switch and key switch has been replaced and it does not.

Start. truck will start if when go to the sileniod and cross jump it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers

Replace the solenoid first. let me know if this doesnt work

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 Ford F150 diagram from battery to relay to seliniod to starer


There is a common issue with this year and I have run into it maybe 100 times, The ignition starter switch (located near the bottom top of the steering column) is defective, the switch halves come apart and this causes a no start. Hook a test light up to the fender solenoid, when the key is held in start position the little wire (solenoid signal wire) should light a 12 volt test light, if not you are not getting any power from the ignition starter switch. The switch is very cheap and easy to replace.

Jun 21, 2016 | Ford Cars & Trucks

1 Answer

Replacing ignition switch


If you have to jump start the car, it had to be either the batter or a connection problem with the battery cables. Having to jump start a vehicle does not have much to do with the ignition switch, unless you are having to jump power to another location to get the car to crank.

Jul 12, 2014 | 1970 Opel Record

2 Answers

Why wont my car start?


If the two you crossed were on the starter solenoid, then it's not getting juice from the ignition switch. Possible reasons include:
Make sure it's in neutral or park, clutch depressed. Then possible problems are bad ignition switch (have you had any problems like having to wiggle the key to get the starter to work?); open fuse (check fusebox); open fusible link or wire (troubleshoot with meter and wiring diagram); bad switch on clutch or gearshift mechanism. (One way to determine if one of the switches is bad is to short it with a wire and see if it starts then.)

May 28, 2014 | 2005 Mazda 6

1 Answer

2006 ford f150 will not start


if you could have a dirty fuel filter.not expensive.not getting gas.

Mar 18, 2013 | 2006 Ford F-150

1 Answer

My car only starts when i cross wire the neutral safety switch. i recently changed out the ignition and it ran for about 3 weeks now nothing! wont turn over at all not even a click (unnless i cross wire...


if your starting the car,by only jumping a wire at the neutral switch,then you more than likely have a bad neutral safety switch that needs to be replaced.

Apr 13, 2011 | 1991 Pontiac Firebird

2 Answers

My vehicle is a 1996 jeep grand cherokee when I turned on the ignition to start it, it feels like it does not go all the way over in start position. But can turn the key on and jump start the...


It sure sounds like the switch, but it may be the key cylinder binding. If the key turns to the same place it used to then replace the switch. If it dosen't then replace the key cylinder.

Feb 12, 2011 | 1996 Jeep Cherokee

1 Answer

I have a 1992 F-150 with a 5.0. The ignition switch block burned up so I replaced it. The truck will not get park to the distributer now. I placed a spark tool between the Distributer and the coil wire and...


it sounds like you have spark in the RUN position, but not in the START position.

try leaving key un RUN position and truck in park wit e brakr applied. Then jump starter at the starter and see if it starts.


if yes, trace circuit from ign switch for start position.

Jan 28, 2011 | Ford F-150 Cars & Trucks

1 Answer

1991 lincoln mark vii lsc runs but not when let the key go back t


its the ignition switch. inside the steering column. at the local parts store. not to expensive part. good luck

Mar 12, 2009 | 1991 Lincoln Mark VII

1 Answer

Replacing starter solenoid


You may have hooked some wires up incorrectly. The smaller diameter wires on the small posts go to different items. One goes to the starter and the other to the ignition. Sometimes the little black bonnets that plug on to the terminals are marked. (S for starter and I for ignition.) You can also jump across the terminals to bypass the ignition switch to see if you even get power to the starter. Let me know what happens.

Mar 05, 2009 | 1988 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...