Question about Dodge Caravan

Open Question

Removing exhaust manifold on 2000 Dodge caravan

Need to replace the freeze plugs

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

INSIGHTAEM
  • 1 Answer

SOURCE: starter for dodge caravan 2000

DISCONNECT THE BATTERY, JACK UP AND SUPPORT YOUR CARAVAN. LYING ON YOUR BACK LOCATE THE STARTER WHICH IS ATTACHED TO THE ENGINE THROUGH THE BELL HOUSING .THERE ARE TWO 15 MILIMETER BOLTS THAT HOLDS THE STARTER ON . AFTER BREAKING THE BOLTS A 15MM WRENCH WOULD BE USEFUL.

Posted on May 30, 2008

  • 548 Answers

SOURCE: replace broken fuel door 2000 dodge caravan

If you're on the smallish side and pretty limber, you might avoid removing the rear wheel. If not, you will likely need to remove the rear wheel and put the van on jack stands securely. I would remove the underside splash shield and gain access from underneath. It looks like you will need to unscrew the plastic insert that surrounds the filler neck inside the area that is exposed when you open the fuel door. Make sure you get the vent hooked up correctly when you are done.

Posted on Jan 31, 2009

SOURCE: replace spark plug 2003 dodge caravan v6

hi the front ones are not bad but the back ones you will have to get from under the van.( do them one at a time)

Posted on Jan 31, 2009

  • 141 Answers

SOURCE: 2000 dodge grand caravan rear heater core tubes need replacing

a lot of pain and heart ache. even on a rack they are a pain . check with your dealer there wae a recall on them for failing its worth the phone call to see kdc744

Posted on Feb 08, 2009

  • 57 Answers

SOURCE: 2000 Dodge Grand Caravan need to know where relay

the cooling fan relay is not in the fuse box.

it is a solid state relay bolted to the radiator core support just behind the bumper

Posted on Jun 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge caravan. Changed engine. Ran a few


defective catalytic convertor. It may be plugged up.Make sure ALL the exhaust line from intake manifold(at engine block) to final exhaust pipe are not clogged up.You have reverse exhaust pressure going back towards engine manifold.

Oct 21, 2014 | 2001 Dodge Caravan

1 Answer

3.8 crack in exhaust manifold whats involved in changeing it


the 3.8 ltr engine is a v6 configuration , so there are two exhaust manifolds... one at the rear (firewall side) and one in front.

the front one is easier to replace of course.

Mar 25, 2013 | 2000 Dodge Grand Caravan

1 Answer

Had exhaust manifold replaced since then my 2001 caravan bucks and blows black smoke little to no power


if you replaced the manifold because it was cracked the look for a plugged cat convertor..the cracked manifold was probably letting the exhaust escape..now it builds too much back pressure

Jul 24, 2012 | 2001 Dodge Caravan

1 Answer

How to replace freeze plug in 1998 dodge ram 1500 pickup


remove engine mounts , sometimes exhaust manifolds. jack up engine drill holes in old pugs use hole to pull out plug install new plugs is all day job for all.

Jul 15, 2012 | 1998 Dodge Ram

1 Answer

What is the easiest way to replace the pigtail on the harness that conects to the upstream o2 sensor on a 1996 dodge grande caravan 3.3L


Just cut and splice. 1 black wire, 1 grey wire, 2 white wires just color match. You may want to remove the upper intake plenum to gain access though. Might as well plan on replacing the o2 sensor while your at it. If the plug got melted because it rested on the exhaust manifold, you probably wont get it unplugged. Not sure where to obtain a replacement plug though. You may have to hit some salvage yards.

Sep 06, 2011 | 1996 Dodge Grand Caravan

2 Answers

How too take the belt tensioner off from the block


The tensioner on that vehicle has a stud made into the assembly. Underneath the vehicle, above the power steering pump, below the exhaust manifold, there is a 15mm nut. you will need a swivel socket and just the right combination of extentions to remove this nut. Once removed the tensioner will pull right off. Make sure to remove the serpentine belt before doing this, and you will probably need an extra hand holding the new tensioner in place while starting and tightening the nut.

Aug 22, 2011 | 2000 Dodge Caravan

1 Answer

I need to remove the exhaust manifold on the driver's side to access a freeze plug at the back of the block. Any special concerns for r&r of the manifold?


May not need to totally remove the manifold. Use a spray lub (I use Movit) and spray the exhaust bolts liberally on cooled down engine. Let sit for an hour or more (or follow instructions on can) Then use 6 point sockets on the bolts and rock back and forth to remove. Once all of the bolts are out you should be able the move the manifold back far enogh to expose the frost plug. When you put the exhaust back on - be sure and use anti-seaze on the bolts along with your new gaskets. Get all of the bolts started before you torque them to spec.

Nov 28, 2010 | 2000 Ford Ranger SuperCab

2 Answers

How to replace spark rear plugs?


The upper part of your intake manifold needs to be removed.I think Chilton lists spark plug replacement on your Caravan at something like 3 hours.

Mar 01, 2010 | 2000 Dodge Caravan

1 Answer

4 cly 98 dodge caravan


Are you sure its the exhaust manifold? I thought so on mine, but turned out to be the crossover pipe. If so, the crossover is only available from dealer and is ~$550. When removing old pipe, bolts are very difficult to get to, and some are only removable from one side (they are studs). I found the site below has excellent instructions with diagrams. Important! Before installing, ensure the bolts fit through the holes in the new part (mine did not).
http://www.popularmechanics.com/automotive/how_to/4218244.html

Jul 12, 2008 | 1998 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...