Question about 1995 GMC Suburban

2 Answers

Blower Fan will not blow, we have already replaced Heater Control

The Heater Fan will not blow, we have already replaced the Heater Control Panel and the Heater Relay behind the Cubby Hole, the fuses are all ok under the hood and on the door panel. Please Help!

Posted by on

  • blueextc3221
    blueextc3221 May 11, 2010

    Have you checked for 12V at the blower fan motor?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

You need to replace the fan ...its under the hood on the passenger side held in bt 3 screws and one plug this is the only motor on that side of the vehicle and only takes a half hour to change out

Posted on Jan 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

Did u replace the fan motor.try to tap on the fan motor see if it comes on.

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconect the control cables on 1997 geo metro heater control?


does the fan work on high.
yes, then the heater resistor block is burned up. replace that
or look at it to see if the coil there are burned up and gone.
please post systems first, then your guess.
the FSM covers all this, step by step, take apart dash. under
HVAC chapter,.
alldata.com log in and its there.
factory service manual.
removing the control is tricky on all cable cars.
you must get the cables loose before the panel can move out.
the cables all clamped down or they will be dead. (all cars with cables drive)
please post of HIGH speed blower works on high first.
why do this the hard way, at the worst we can use a voltmeter
and prove what is dead, first.

see those rules on cables in the FSM below?
ill not post the panel Remove
  1. Disconnect the negative battery cable.
  2. Remove the heater control unit from the instrument panel.
  3. Remove the mode and temperature control cables at the heater case. Remove the cables from the vehicle.
  4. Remove the fresh/recirculate control cable at blower case and remove from vehicle.
  5. Installation is the reverse of removal.
  6. Adjust the cables prior to attaching at heater control unit.

now lets look at the blower, dead, on all speeds but HIGH , i bet.
?????????????????
this is your cave man simple blower
so if FUSE marked HTR is good, and 12vdc is on both sides of
fuse keyon, then it is good,. and 12vdc lands on motor top
where below on HIGH the blower and switch works on high.
if say the right side resistor blows up, (as all do)
then all lower speed fail. and DC power fails to reach the fan motor.
how is that? clear>?

25490481-331th0o4ygoodik5f23zyrbq-3-0.jpg

Feb 27, 2015 | 1997 Geo Metro

1 Answer

2011 Nissan Titan heater/ac fan blows on high we replaced the VBC it did not fix it, now what?


What is VBC? Ah, probably Variable Blower Control? my guess you got wires crossed, or a short around the control or even direct short to hot (12vdc) wire. Double check your work, wire connections. Instructions? with the new? double check.

Feb 27, 2015 | 2011 Nissan Titan Crew

3 Answers

How do I change heater fan


It would help to know the make and model. Different manufacturers put them in different places and mount them different.

Feb 19, 2015 | Cars & Trucks

1 Answer

Heater (fan) not working


well the blower work on HIGH>?
if the blower i dead on high , replace the fuse. called blower
if the fuse is good, then the blower is bad , the controls to it are bad
the FSM covers all the tests.
if not DIY person, take it in for service.
or look on alldata.com (online, almost FSM)

Feb 04, 2014 | 2006 Toyota 4Runner

1 Answer

Location for blower motor/heater/fan fuse?


Before you rip, check the 30A HEATER CIRCUIT BREAKER in the instrument panel fuse panel. The input is hot with the engine running. CB output connects directly to the heater blower motor. A cluster of heater blower motor resistors determines blower speed as selected by the blower switch in the heater control assembly. The switch setting is sent to the powertrain control module (PCM) which acts to turn the blower motor on at the selected speed.

Sep 22, 2012 | 1994 Ford Escort

1 Answer

1992 323 mazda want blow heat out


REPLACE THERMOSTAT.IF ALREADY DONE.CHECK HEATER BLOWER MOTOR SEE IF POWER GOING TO HEATER BLOWER MOTOR.IF YES BLOWER MOTOR BAD.IF NO POWER GOING TO BLOWER MOTOR CHECK AC AND HEATER CONTROL FUSE AND CHECK BLOWER MOTOR FUSE AND RELAY IF ALL IS GOOD CHECK SEE IF POWER GOING TO AC AND HEATER CONTROL SWITCH IF YES THE AC AND HEATER CONTROL SWITCH COULD BE BAD.

Nov 10, 2011 | 1991 Mazda 323

1 Answer

Why wont my a/c or heater fan come on?


When the blower works only on the high setting its usually a bad blower resistor which is right near the blower motor. now you say it would always blow high regardless of the fan speed setting that would indicate probably the climate control unit or a connector problem somewhere. finally it not working at all may be the climate control unit or connection went bad even further. it might have a blown fuse or a bad blower motor in addition to the climate control unit or connector problem .check for power and ground at the blower motor. the power is supplied from fuses and may have a relay also. the ground is supplied from the climate control unit and goes through the resistor to control the fan speed. good luck

Oct 30, 2011 | 1997 Lincoln Continental

2 Answers

I have a 1979 oldsmobile delta88 for several years.My blower motor stays on and blows at a constant low speed and doesnt blow much on high.I already replaced sll components except for thewhole a/c switch...


REPLACE BLOWER MOTOR RESISTOR. IF YOU GET ONLY ONE CONTROL SPEED.IF YOU HAVE ALREADY REPLACE BLOWER MOTOR RESISTOR.BLOWER MOTOR CONTROL SWITCH BAD. REASON BLOWER STAY ON ALL THE TIME.FAN BLOWER MOTOR RELAY BAD.
.

Aug 25, 2011 | Oldsmobile Delta 88 Cars & Trucks

1 Answer

Heater control only works on high and fan doesnt blow heat thru the vents sounds like its a fan being blown in the wind.


100%: Heater Control on High Only?
This is the Blower Motor Resistor that needs to be replaced. It is located adjacent to the Blower Motor.

Jan 28, 2010 | 2000 Oldsmobile Alero

2 Answers

A/c heater won't blow... Blower works even replaced with new blower but still won't blow... Is there a relay to replace? The fuse for a/c is good


did you check to see if the a/c belt is still on the a/c puller ? if so then try a flush of all hoses.

Oct 25, 2009 | 1998 GMC Blazer

Not finding what you are looking for?
1995 GMC Suburban Logo

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...