Question about 1994 Dodge Caravan

1 Answer

Engine pullies the pullies on side of enginq

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,432 Answers

What is wrong with the pulleys?

Posted on Feb 21, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 CRX LX, 1.5l engine. Where are the timing marks?


The cam have two notches on the side Wich have to line horizontal with the engine cover surface along with the cam spoke label up.
the crank pully also have some mark but it's on the inner side of the crank pully beside the engine belt usually a few close together and one by itself lining up to the timing cover above the crank pully

Jul 15, 2015 | Honda Cars & Trucks

2 Answers

I have a 2000 dodge caravan 3.0 engine there a sqeak noise when i first crank the motor up until it warms up i replaced the idler pully 6 months ago but it still sqeaks i can move the tensioner pully a...


I can't say for sure but it could be the tensioner pully. I don't think you should be able to move it side to side. That would indicate that the bearing is worn.

Nov 03, 2017 | 2000 Dodge Caravan

1 Answer

Whaere is the water pump located


The water pump is on the top right hand side of the engine if you standing on the passenger side looking at the front of the engine. Keep in mind that the water pump only goes back on one way, so make sure that you have it clocked right or the bolts wont line back up. Remove the water pump pully first before you take the belt off. This makes it easier to break the pully bolts loose and then remove the water pump bolts. Then after, put the pully back on and then the belt and then tighten the pully bolts, the belt will help hod the pully for you.


360dreamworx_44.gif
360dreamworx_45.gif
360dreamworx_46.gif

Aug 08, 2011 | 2003 Buick Rendezvous

1 Answer

Serpintine belt routing for a 2002 dodge ram 1500 with a 5.9 l engine


this is farely easy to figure out from looking at your pullies. ribbed pullies normaly take the ribbed side of the belt and smooth pullies take the smooth side of the belt. i would start at the tentioner pully (which is smooth) the put the inside of the belt around the 2 nearest pullies and weave it alternating in and out of the rest of the pullies.

Jan 29, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

How is going serpentine belt on 3.6 engine by suzuki 2007


the universal rule for serpentine belts is, ribbed pully is front side of the belt and shiny pully is back side of the belt, there should also be a one tensioner pully that is either spring loaded or tighten by a screw.

Nov 05, 2010 | 2007 Suzuki XL-7

1 Answer

Do you have a way to find the route for a 1993 Ford Escort Serpentine Belt?


FOR A 1.9L ENGINE. CANT SEND PIC, START BY PUTTING BELT OVER ALTERNATOR PULLY,THEN TO THE RIGHT OF POWER STEERING PUMP PULLY FROM THERE TO THE LEFT SIDE OF THE IDLER PULLY , THEN UNDER THE A/C COMPR PULLY AND UNDER THE CRANK PULLY RELEASE TENSION ON TENSIONER BELT GOS UNDER TENSIONER.

Nov 04, 2009 | 1993 Ford Escort 4 Door

1 Answer

How to set timing marks when changing the timing belt 1995 kia sportage 2.0liter


There is a DOHC or SOHC (double or Single overhead cam engone. Both are Similar. Both have a notch on back side of crank pully that aligns with a tab on engine just above crank pully looks like a triangle with the tip near crank pully is rounded off. SOHC engines have an arrow on cam pully that aligns with a point at top of timing belt rear housing. about straight up at top of it. DOHC have an I and an E on the cam pullys I for INTAKE and E for EXHAUST. the I and E match up at same type points on top of rear Timing belt housing. When installing belt make sure you do not move pullys. put belt on starting with cam shaft (s) then down to crank on tension side which looking at motor will be the right side or Clockwise direction keeping it tight no, or EXTREEMLY little slack. then back up around tensioner. Tensioner should be the last pully to go around. Once on make sure timing marks still lline up.Adjust tensioner and. rotate engine BY HAND 4 times and re check marks.

Oct 09, 2009 | 1995 Kia Sportage

1 Answer

Need diagram to install serpentine belt


Look at the pullies to see if they are smooth or if they have lines on then. The back side of the belt the ( smooth side) goes against the smooth pullies.The side with lines on it goes to the other pullies. Some vehicles have the diagran in the engine compartment. Under the hood or by the top of the radiater.

May 10, 2009 | 2001 Isuzu Rodeo

1 Answer

Cant put on belt right


from front of engine looking back,belt around bottom of crank pully,water pump is just above,left side of belt comes around water pump going counter clock wise,put belt over alternator,then straight across to a/c compressor,(make sure belt goes under any idler pullies,smooth side of belt to smooth side of pully)find your belt tensioner,pry back on tensioner(be carefull)and carefully place belt under roller pully of the tensioner,release and check allignment of belt prior to starting.oh ya make sure belt is in good condition.

Mar 01, 2009 | 1991 Chevrolet C1500

2 Answers

Serpentine belt came off need to know how it goes back on


this is hard to exsplain without showing you a photo ,but i will try. first get the belt around the engine crankshaft which is the pully closest to the bottom and center of the engine. when standing in front of engine start to lead the belt to the right and connect to power steering pump then up to generator, next thare is going to be a smooth pully not groved like the others to the left,put the smooth side of the belt on bottom of this pully and continue left to the ac/compressor go around ac/compressor andstraight down to the belt tensioner , and then right over to the water pump which has a smooth pully not grooved. remember the smooth pullys will always carry the smooth side of the belt and the grooved pullys the grooved side of belt. the belt tensioner will half to be released by a serpantine belt tensioner tool sold at your local auto parts store. these instructions is for 3.8 liter engine, if you have a 4.6 liter engine it will be different, so repost stating that you have a 4.6 if this dont help

Dec 22, 2008 | 1997 Mercury Cougar XR7

Not finding what you are looking for?
1994 Dodge Caravan Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...