Question about Cars & Trucks
It will be one of two sources the water could be coming through the windshield seal or the rubber seal around the door. To find the source of the leak get some tape and tape the opening around the door and window, then use a garden hose and wet the windshield and door using low volume of water. If there is new water in your car the windshield is the problem and will need to be resealed at your local auto glass shop.
Posted on Jan 18, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
*The Turn signal on the Side of the car next to the headlight*
1. Open the retractable headlights.
2. Remove the plastic shroud around the headlight: two screws in front and one on each side.
3. Look to the outside of the headlight and you will see a single screw in a small plastic cover on the front inside edge of the signal light assembly. The headlight prevents you from getting at the screw straight-on. I broke it loose with an offset phillips screwdriver, and then backed it out with a regular phillips.
4. Remove the plastic cover, and you will see two screws. Remove them.
5. Now you can pull the turn signal assembly forward and out.
6. To remove the bulb holders from the assembly, twist counterclockwise and pull out.
7. Pull straight outward to remove the bulbs. To assemble, follow the steps in reverse. Note that there are two plastic rods on the back end of the turn signal assembly that you will insert into two holes in the channel of the fender
*The turn signal in the bumper*
1. You will need a phillips head And Flat head screw driver, right below the turn signal there is a panel that you can pop out, (or its allready gone, Looks like a Fog light can go in there.)
2. once u find that, (Pretty easy to find) Look directly up in there., there is styrofoam up there and u will also notice a little hole,
3. Stick the Phillips head screw driver in that hole and turn it counter clockwize, The screw will not fall out,
4.once it feels like the screw is loose put the flat head in between the turn signal lense and bumper, the side where you unscrewed it and SLOWLY pry it out,
4. once out, just twist the plug and replace light bulb
to replace just reverse instructions
Posted on Jun 30, 2008
SOURCE: Interior Carpet Getting Wet
It sounds like a plugged drain line from the air conditioner. Most cars now run in the a/c mode whenever u turn on the climate control (even when heat is on). The passenger side front is where it would be wet, and the carpet and carpet pad act like a sponge and will soak up the water. Let me know how u make out.
Posted on Oct 25, 2008
TPMS Tire Pressure Monitoring System
Check ALL including the spare tire for proper air pressure. If all is well then check the fuse for the TPMS module. If all is well there, off to the dealer you may have to go.
Posted on Jul 17, 2009
if you do not have original anti-theft radio code you will need to remove radio and retrieve s/n off of radio. once you have that you can go into nearest honda dealer and with s/n they can give you correct radio code
Posted on Jul 25, 2009
no, 12mm wrench or ratchet on 12mm socket. the piston is tough to push back in. its a twist in type and you will need some force to push and twist the piston back in. - note rear brake pads wearing out on the new 08-09 accords are very common and if under 16-18 thousand miles it may be covered. honda knows about this problem
Posted on Oct 27, 2009
Tips for a great answer:
May 31, 2016 | 2009 Chevrolet Chevrolet HHR LT
Jan 06, 2016 | Cars & Trucks
Aug 12, 2015 | GMC Cars & Trucks
Jul 28, 2014 | 2009 Nissan Altima
Feb 12, 2010 | 2005 Chevrolet Colorado
Sep 20, 2009 | 2003 Honda Accord
May 21, 2009 | 2000 Ford Expedition
May 12, 2009 | 1991 Honda Accord
Oct 25, 2008 | 2003 Honda Accord
185 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: