Question about 1999 Chevrolet Blazer

1 Answer

4 wheel drive is stuck on

I noticed my 4 wheel drive was on when i headed in to work, i pushed the 2 wheel button, to disengage the 4 wheel, but it poped right back into 4 wheel. how do it get the truck back in 2 wheel drive?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Try going to 2WD while in neutral. Then take it to the shop to check it out.

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 366 Answers

SOURCE: my truck is stuck in 4 lo

pull atc 25 amp fuse in underhood fuse center and 10 amp 4wd fuse inside cars fuse box,your problem is in control box behind kick panel on pass. side ,corrosion build up,

Posted on Mar 06, 2009

  • 2 Answers

SOURCE: when you push the 4

a lot of 4wd you have to back up for a few feet to disengage the hubs after you tourn them back to 2wd

Posted on Dec 13, 2008

  • 99 Answers

SOURCE: 2004 Suburban 4 wheel drive

set as default most likely either that or computer error. please email me at meanness628@aim.com with any other info or questions

Posted on Sep 30, 2008

  • 2 Answers

SOURCE: My 98 s10 is stuck in 4 wheel drive low.

Pull the kick panel on the passenger side. there is a small box mounted there that is the computer that controls the actuator for the 4wd system. this is notorious for problems due in fact that the connector likes to pull out and away from the module. I had the same problem and the solution is simple.. take a long zip tie and get it between a few of the wires and around the module. tie it in and have a nice day.. it wont come off or try to pop out anymore and you should have no issues getting into 2wd, 4wd h, 4wd L.


Posted on Jun 21, 2009

AaronTech
  • 115 Answers

SOURCE: lights on push button 4 wheel drive out

more than likely there is a code set for the 4 wheel drive system and its stuck in a "limp in" mode. you're going to need to get your hands on a code reader or take it in to the dealer for a diagnosis.

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 02 Suburban won't disengage 4.wheel drive. The


This is a mechanical technicality that U can't fix at home, you need an expert to reset the system for you

Sep 09, 2013 | Cars & Trucks

1 Answer

My gr is stuck on 4x4 and won't go to 2wd


Usually if you push the button to go back to 2 wheel drive and back up a few feet it will let the axle hub disengage.

Aug 30, 2012 | 1998 Chevrolet Blazer

2 Answers

4wd is stuck in 4low was going to try to disconnect the 4wd so i could get it back to 2wheel to be able to drive it how do i do this


Its a vacuum opperated system. There is a vacuum line on the transmission but ufrortantly the transmission will not work correctly with this disconnected. That controls what is called an actuator its a vacuum moter its located under the battery tray and this pulls on the cable that makes it shift in and out of 4 wheel drive.Try disconnecting the cable at the actuator and pulling back away from the engine this may pull part # 9 the carrier conector out of the out put shaft part # 23 and disengage the 4 wheel so you can drive in 2 wheel with no side affects although you would have to replace # 9 or # 23 or bolth to make the 4 wheel work again but then again if you do this it may workthe gears just got bound up and it might work but i wouldn't push my luck with it until it was apart and could inspect the parts.

Dec 28, 2010 | 1999 Chevrolet Blazer

1 Answer

4 wheel drive will not disengage


take a standard screwdriver apply pressure to the whole switch panel towrds the drivers window then repeatedly push the 2 wheel drive button until the low lock button flashes then keep on pushing 2wheel drive button til it shifts you can tell its out by cranking steering wheel all the way to either end of travel and move foward no binding means your out

Sep 25, 2010 | 2000 Chevrolet Silverado 1500

2 Answers

4 wheel drive wont disengage


PUT IT IN DRIVE AND ROLL JUST A LITTEL AND MOVE THE TRANS STICK TO #2,ALL THE WAY UP.IF THIS DONT DO IT,THEN YOU HAVE A LINK PROBLUM

Aug 20, 2009 | 1993 Jeep Grand Cherokee

1 Answer

GMC Sierra 4 wheel drive won't disengage


i had the same issue change push button cluster

May 04, 2009 | GMC Sierra 1500 Cars & Trucks

3 Answers

My truck is stuck in 4 lo


pull atc 25 amp fuse in underhood fuse center and 10 amp 4wd fuse inside cars fuse box,your problem is in control box behind kick panel on pass. side ,corrosion build up,

Mar 06, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...