Question about 1991 Honda Accord

1 Answer

When i put the brakes on the front end shaks - 1991 Honda Accord

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 248 Answers

Uneven brake wear due to calipur issue. Could be ABS playing up. Faulty master cylinder. Damaged / warped rotors.

Posted on Jan 18, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front end popping noise


There are so many possibilities. It's difficult to even attempt a guess.but... Axles, ball joints, brake calipers, rotors, sway bar ends/bushings, rack and pinion,tie rod ends, A-arms, shocks, struts, springs, mounts and even a cracked or broken frame! Hope this was helpful!

Oct 20, 2013 | Cars & Trucks

1 Answer

I have a 1999 Chevy Silverado 2500 4x4 with a front rear end that is froze up


first start by bleeding the brakes and at the same time replace the brake fluid. on your rear end run some lucas for rear ends same for the front and see what happens.

Jan 28, 2013 | 1999 Chevrolet Silverado 2500

1 Answer

I recently put new front brake pads and had rotors turned on the front end of my 2003 tundra sr5,after a month of driving i'm getting the pulsation when braking back which is why i made this repai


HI if you have pulsation after a month you must replace the rotors
they are too thin and the heat is warping them faster then before you
had them turned
note you replace brake pads and rotors

good luck

Feb 20, 2012 | 2003 Toyota Tundra

2 Answers

Steering wheel wobbles when driving slowly and in a straight line


you need to have your tires checked for a slipped belt, also if you get a shake in the steering wheel when you apply the brake you need to have the brake rotors re-surfaced or replaced.

Feb 03, 2011 | Ford Focus Cars & Trucks

1 Answer

My abs & brake lights go on & off brake pedal seems soft brake fluid - ok, no leaks, has new brake lines, slamming on the brakes locks 'em up. no abs, right? 2000 gmc jimmy 4.3


Sounds like you might have air in the brake system. You will need to bleed the brakes to remove air. Start with the passenger back wheel. use a small hose and submerge the end in a glass bottle filled 1/3 full of brake fluid. The other end goes on the nipple of the brake bleeder. Have someone pump the brakes and then hold the pedal down then loosen the bleeder. then tighten the bleeder. you should see bubbles in the brake fluid. Keep repeating this procedure until you see no bubbles. You might have to put as much as 1 quart of brake fluid thru each wheel to remove air. Then you do the driver side rear followed bypassenger side front and finally driver side front

Aug 11, 2010 | 2000 GMC Jimmy

1 Answer

Should the brake rotor be loose when you take the wheel off? I have been experiencing popping noises from the front end going over bumps as well as putting on the brakes. Just pulled the right front tire...


The wheel holds it on tight. What you see is how it is. The rotor shouldn't have much of a step or ridge on the outer edge. You can remove the rotor and file or sand it off or have them turned at the auto parts store. Then sand off all rust on pad sliding surfaces and put anti-seize on those areas. That eliminates the front brakes. Check out sway bar bushings and end links, if applicable.

Mar 11, 2010 | 2002 Chrysler Sebring

1 Answer

Replace front brake pads


Losen your lug nuts on both front tires and jack up the front end. You need to remove the calipers (the piece that holding the brake pads) Two bolts behind the caliper. Pop the the brake pads off and depress the brakes ( you will need a clamp to depress it) Put on the new brake pads. Tools needed : clamp, flat head screww driver, soket set, brake cleaner

Jan 20, 2010 | 2000 Hyundai Accent

1 Answer

2002 axiom front brakes


The tires could be out of balance, maybe you clipped a curb. Or your front end could be about nto pass you. Id have the ball joints and tie rod ends looked at. Usually front end wobble leads to more serious issues quickly.

Jul 19, 2009 | 2002 Isuzu Axiom

1 Answer

Clunk when shifting car into drive from park 1990 ford taurus.


If the front end vibrates when you put the brakes on it could be a few different problems. Your need to check the brakes, they may be worn. if the back brakes are worn your front brakes are doing all the stopping. if your brakes are fine then you are looking at the front control arms or the upper and lower ball joints. You can take your car to a brake and front end shop for a free estimate. You are probably looking at about 400 to 1200 dollars.
I hope this helps you out

Nov 28, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...