Question about 2008 Ford Explorer
I do not know if my ford explorer 2008 has Bluetooth or not Can I pair my iPhone 5 to it? There is no sync option in my car Thanks Khaled
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1997 ford explorer V8 5.0 engine
P1405-Differential Pressure Feedback Electronic (DPFE) sensor upstream hose off or plugged - or cracked.
I believe it is on the driver's side of engine about half-way down. also, check all other hoses for damage
Posted on Jun 04, 2008
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
Removal and Installation
Posted on Apr 04, 2010
Testimonial: "thanks mate!"
I have hearing a lot of this lately with Fords. Most of the time this dash board light comes on due to problems with the Throttle Body (TB)not just your coolant,etc.. If it is sticking,dirty,causing misfires,etc. then this can cause an engine fail safe mode.You might first try putting in some injector cleaner and a higher grade of gas.Many people I know who have had this problem have had to have their TB cleaned and/or replaced. This is something Ford dealerships now about,but hasn't been made a recall or anything.There are service bulletins though.Mainly keeping cleaner in your gas and performing ritual tune-ups/oil changes may be the only thing you can do.Hope this helps
Posted on Apr 17, 2010
Tips for a great answer:
May 04, 2016 | 2007 Mini Cooper Convertible
Jan 27, 2016 | 2006 Ford Focus 2.0
Jan 22, 2016 | 2008 Toyota Tundra CrewMax
Dec 15, 2015 | 2002 Ford Explorer
Jun 20, 2011 | 2008 Acura Mdx
Feb 04, 2011 | 2008 Ford Focus
Apr 06, 2009 | 2008 Acura Mdx
Sep 11, 2008 | 2008 Ford Focus SE Sedan
Jul 08, 2008 | 2008 Ford Taurus Sedan
126 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: