Question about Oldsmobile Intrigue

Open Question

2000 Olds INtrigue Inner Tie Rod - Intrigue Oldsmobile Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 124 Answers

SOURCE: I,ve disconected the tie rod

If it is the inner tie rod you are working on it need to be threaded out on some you can get with a wrench but most you will need an inner tie rod tool. Look at your replacement tie rod you will see the threads and two flat spots that is where the wrench goes. Please rate.

Posted on Dec 13, 2008

MNfisherman
  • 11896 Answers

SOURCE: Loose inner tie rod, driver's side

There is a lot of information to type here. I am not trying to be lazy, but this will help you more.
This is an illustrated guide with step by step directions.
Copy and paste into your browser:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c15280040ce5

Posted on Jan 17, 2009

  • 90 Answers

SOURCE: tie rod problem 98 Dodge

Yes, there's a special tool called an "inner tie rod tool". It has special crowsfoot type pieces that attach to a long tube with a 1/2' drive ratchet hole in it. First, remove the outer tie rod (COUNT THE # OF REVOLUTIONS WHILE UNSCREWING IT!!) Take off the jamb nut. Take the boot off. Use the tool to remove and replace the inner tie rod. Re-install the boot, jamb nut, and outer tie rod. If you count the # of turns it takes to remove the outer tierod, you'll be able to set it back where it was enough to drive it. i still recommend an alignment though.

Posted on Feb 16, 2009

  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Dodge Grand caravan Inner tie rod end


use a pipe wrench also known as a monkey wrench that will work just make sure there is not a lock screw keeping it from turning some aftermarket inner tierods have alittle allen head screw to keep them from turning

Aug 27, 2012 | 2000 Dodge Grand Caravan

1 Answer

2003 olds alero has slack in steering replaced tie rod ends did not help hhobdy@hotmail.com


I have seen racks come loose on aleros and grand am's. Did you replace the inner tie rod ends, they may also be worn, you also have a small U joint on your steering shaft. I hope this all helps.

Oct 22, 2010 | 2003 Oldsmobile Alero

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

1 Answer

How do you change the wheel sensors on a 2002 olds intrigue


They are integral with the hubs, so you need to change them. Not a bad job, but you need good tools. Remove the tire, remove the tie rod end and ball joint, remove the axle, remove the caliper, remove the bolts, drive out the old hub, installation is reverse.

Apr 07, 2010 | 2002 Oldsmobile Intrigue

1 Answer

How do you remove and replace the power steering hose on a 2001 Olds Intrigue?


16mm flare nut wrench. Make sure you replace o-rings. May have to remove sway bar and drop rear bolts on cradle. Route under right tie rod end.

Mar 04, 2010 | 2001 Oldsmobile Intrigue

2 Answers

2000 LINCOLN LS - Outer tie rod removal assistance


Yes degreaser will not hurt it. The outer tie rod is retained only by one nut that connects it to the inner tie rod.Once you have this loosen just turn the outer tie rod to the left to remove it from the inner tie rod.

Feb 24, 2010 | 2000 Lincoln LS

1 Answer

How to change inner tie rod 2000 saturn sl


CHECK OUT THE INNER TIE ROD TOOL FROM (KD TOOLS IT WILL WORK ON ALMOST ANY RACK&PINION SYSTEM OUT THERE)

Feb 07, 2010 | 2000 Saturn SL

2 Answers

Am changing the inner tie rod on a 2000 cirrus with a 2.5 and cant figure out how to get old one off


to get the inner tie rod out you need an inner tie rod tool, it's a long tube that fits a 1/2 inch drive rachet and there's different size adaptors that go into the end of it to fit over the tie rod, find the right size put into tool, put over tie rod and brake it loose, reverse for installtion.

Nov 18, 2009 | 2000 Chrysler Cirrus

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

2 Answers

Replacing outer tie rod on a 2000 dodge neon


put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Oct 03, 2008 | 2000 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...