Question about 2000 Isuzu Rodeo

Open Question

Como poner a tiempo motor isuzu rodeo modelo 2000

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1751 Answers

SOURCE: Como hacer la instalacion de la sincronizacion de

Hi

you need to mark it as lonh form the center you can
and keep it with dot tape at that points

Posted on Nov 25, 2010

ZJLimited
  • 17970 Answers

SOURCE: como colocar el tiempo de

Saludos, sugiero usar algun traductor para resolver estos detalles, obtenidos de un Boletin Tecnico de Servicio (TSB = Technical Service Bulletin)

A couple things you may want to be aware of, before getting too deep into this one:
(1) There is a factory recall under which the timing belt and sometimes tensioner components are replaced on this vehicle. you may want to check with the dealer to see if yours is still under an open recall for this; if so, they will replace the timing belt and any necessary related components for free. The recall is #01L002000 (description follows):

This is not a safety defect in accordance with the Safety Act. However, it is deemed a safety improvement campaign by the agency.

Vehicle Description: 1998-2000 Rodeo (UE) and Amigo (UA) models equipped with 2.2L 4-cylinder engines. The timing belt could break before the recommended scheduled maintenance.

This condition could cause the engine to crank but will not start or the engine could stall while driving and will not restart.

Dealer will inspect the vehicle to determine the condition of the timing belt and tensioner. The dealer will replace the timing belt. Depending on the condition or model of the timing belt tensioner, the tensioner may also be replaced. Isuzu has decided to conduct a Service Campaign to replace the timing belt. Owners can contact Isuzu at 1-800-643-4070, ext. 426, concerning this program

Second, there is a revised procedure involved in indexing the camshafts during timing belt replacement. This is most likely not detailed in your Haynes manual, but is outlined in an Isuzu service bulletin. Here is the procedure as described in the TSB:

BULLETIN NUMBER: IB00-S005
GROUP: INFORMATION
ISSUE DATE: FEBRUARY 2000

3.5L V6 DOHC (6VE1) / 3.2L V6 DOHC (6VD1) ENGINES: TIMING BELT INSTALLATION

AFFECTED VEHICLES: The following models equipped with "Direct Attack" DOHC 3.2L / 3.5L V6 engine:
^ 1998-2000 Rodeo (UE)/ Amigo(UA)
^ 1998-2000 Trooper (UX)
^ 1999-2000 VehiCROSS (VX)

SERVICE INFORMATION
This information bulletin outlines the proper steps to index the camshafts with the crankshaft. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, this is important prior to timing belt installation. Due to the gear-ratio used by each camshaft pulley to drive the camshafts, engine timing cannot be indexed conventionally.

SERVICE PROCEDURE

IMPORTANT: In the following procedures, the references to 9 or 12 O'clock positions are based on deck plane of the cylinder deck-to-cylinder head mating surface (as viewed from the front of the engine), and NOT RELATIVE TO THE SHOP FLOOR.

1. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, please proceed to Step 2. Otherwise, continue with Step 22 for timing belt servicing procedures. (after removal of front timing belt covers as outlined in the appropriate Workshop Manual).

2. After cylinder head servicing as outlined in the appropriate Workshop manual, proceed to the following steps.
3. Lubricate and install the idler gear.
4. Inspect the idler gear retaining cover for wear.

NOTE: There is a 0.039 lubrication hole drilled into the idler gear retaining cover. Always inspect this hole for obstruction.

IMPORTANT: Do not use a liquid gasket material on the idler retaining cover. Always replace the retaining cover with a new 0-ring. Be sure to lubricate the 0-ring prior to installation.

5. Install the idler cover and torque (10 Nm, 8 lb ft) the 6 mm bolts
6. Align the right bank idler shaft alignment marks.

IMPORTANT: Align the idler gear dowel pin to its corresponding mark on the idler gear retaining cover before installing the camshafts

7. Use special J-tool to pre-load the sub gear assembly.

NOTE: Use special J-tool J-42686. Once the sub-gear has been pre-loaded, install the 5 mm bolt supplied with the tool and insert it into the camshaft from the back of the camshaft gear assembly. Tighten the bolt to lock the sub-gear in place.

IMPORTANT: When the sub gear is pre loaded, the teeth on the sub gear should be aligned with the teeth on the camshaft gear.

8. Install the odd bank camshaft(s) into the cylinder head.

NOTE: Before installing the camshafts, pre-lube the cam lobes using a suitable molybdenum assembly grease

IMPORTANT: The single dot on the camshaft gears must be aligned with their corresponding marks on the idler gear. Also, do not remove the 5mm bolt holding the sub-gear, until the camshaft journal caps are installed and the bolts are torqued.

9. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-matching. However, pay close attention when installing the caps on the odd bank cylinders. because the cap arrows will face the front of the cylinder head.

10. Place a small amount of RTV sealer on the head surface where the cap contacts the head surface.
11. Repeat Steps 3-5 for even bank cylinders.
12. Align the left bank idler shaft marks (Refer to figure 3).
13. Pre-load the sub-gear assemblies (Refer to figure 4).
14. Install the even bank camshafts and pre-lube the cam lobes using a suitable molybdenum assembly grease (Refer to figure 5).
15. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-match mg. However, pay close attention when installing the caps on the even bank cylinders, because the cap arrows will face the rear of the cylinder head.


continue...

Posted on Aug 17, 2011

  • 1 Answer

SOURCE: como se coloca la cadena de tiempo de Isuzu Rodeo

Pudiste resolver tu problema? yo teengo la misma situacion ahora me podrias ayudar?

Posted on Jan 02, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Como poner en tiempo una Cadillac escalade 2000..


como poner en tiempo un cadila escalalde del 19999

May 07, 2013 | Cars & Trucks

1 Answer

Diagrama para poner a tiempo motor l20b nissn


como poner a tiempo un motor nissan L20B

Sep 24, 2012 | Nissan Nissan Cars & Trucks

1 Answer

Como poner banda del tiempo a una isuzu 99


COMO PONER BANDA DE TIEMPO DE UNA ISUZU RODEO 99

May 28, 2012 | 1999 Isuzu Rodeo

1 Answer

Como hacer la instalacion de la sincronizacion de la banda de tiempo de una isuzu rodeo 1998, motor y22?


Hi

you need to mark it as lonh form the center you can
and keep it with dot tape at that points

Nov 25, 2010 | 1998 Isuzu Rodeo

1 Answer

Como pongo en tiempo el buick lesabre 1997


usa el link de www.autozone.com y ahi puede escoger su tipo de auto y despues de poner la informacion busque con el search-- maual de carro y ahi le dice como poner el tiempo

Mar 30, 2010 | 1997 Buick LeSabre

1 Answer

La posicion dela banda del tiempo de caravan 3


como poner la banda de tiempo a una dodge grand caravan 1994,motor 3.0

Jan 17, 2010 | 1989 Dodge Caravan Cargo

9 Answers

Poner a tiempo cadenas de distribucion ford motor 4.0 mod 2002


11marzo2010- Necesito que me Hagan favor de enviar el diagrama para poner un motor de un tiempo de 4,0 Ford Explorer

Sep 14, 2008 | 2006 Ford Explorer

1 Answer

Engine swap


como poner el tiempo de cadillac deville modelo 97 8 cilindros 4.6 litros 32 valvulas

Jul 16, 2008 | 1997 Cadillac DeVille

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...