Question about 2001 Daewoo Lanos

1 Answer

Changing alternator on 2001 Daewoo Lanos

I am attempting to remove alternator from my 2001 Lanos and the lower pivot bolt is hitting something on the engine preventing me from removing it. Do I have to drop engine & transmission to remove this alternator

Posted by on

  • Rick Byrd
    Rick Byrd May 11, 2010

    is it possible that this bracket with the pivot point , can be removed with the alternator still connected to it , and reverse procedure to install ? or sometimes you might take a floor jack and a piece of wood and put under the oil pan , carefully support the engine , undo a motor mount or 2 and raise or lower the engine slightly so that this bolt in question can clear its obstacle ..

    J5

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 5,568 Answers

Probably not.
You may have to remove brackets or belts but I've yet to see one for which one couldn't find a 'work-around.'
No doubt that the engine/transmission assembly was dropped in as a unit, but their service people still have to deal with removals such as yours so considerations such as removing a specific part is normally part of their design process. Just imagine if this had to be done under warranty and Daewoo would have to pay the bill. 

Posted on Jan 25, 2009

  • MasterMarv Nov 19, 2010

    I know this is late, and I'm sure you have solved you issue by now, but NO you do not have to drop the engine or anything in order to get to that bolt. Just a ratchet and an extension and you will be fine. I've had to do this many times when going through a trial and error process. (The plastic pipe coming from the water pump cracked and it was a pain to find a replacement, so I tried a few home made rigs. I had to drop the alt back and take off the intake manifold each time)

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

1 Answer

How do I change the alternator on a 1999 dodge intrepid


Check thid procedure... Removal & Installation

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Lower plastic splash shield Transmission cooler and position it aside Lower radiator crossmember support
  3. Loosen but do not remove:
    Adjusting -T- bolt and the pivot bolt Drive belt adjusting bolt
  4. Remove or disconnect the following:
    Drive belt Alternator field circuit plug Alternator B+ terminal nut and wire Pivot bolt; be careful not to lose the spacer Alternator

    zjlimited_992.jpg

    Fig. The location of the generator on the 2.7L Engine

To install:
  1. Install or connect the following:
    Alternator Pivot bolt with the spacer and leave loose Alternator field circuit plug Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm) Drive belt
  2. Using a belt tension gauge, torque the adjusting -T- bolt until the tension gauge reads 120 lbs. (534 N) for a used belt or 180-200 lbs. (792-880 N) for a new belt.
    Lower radiator crossmember support Transmission cooler Lower plastic splash shield Negative battery cable
  3. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).

3.2L & 3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.

  2. Remove or disconnect the following:
    Negative battery cable Lower mounting bolt and pivot bolt Drive belt tension bolt Drive belt Bracket, lower mounting bolt and pivot bolt Alternator Alternator field circuit plug Alternator B+ terminal nut and wire

    zjlimited_993.jpg

    Fig. The location of the generator on the 3.2L and 3.5L engines

To install:
  1. Install or connect the following:
    Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm) Alternator field circuit plug Alternator Drive belt Pivot bolt and lower mounting bolt
  2. Using a belt tension gauge, torque the -V- drive belt until the tension gauge reads 120 lbs. (534 N) for a used belt or 140-160 lbs. (623-711 N) for a new belt.
  3. Using a belt tension gauge, torque the Poly -V- belt until the tension gauge reads 120 lbs. (534 N) for a used belt or 180-200 lbs. (792-880 N) for a new belt.
  4. Install the bracket.
  5. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm)
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).
  6. Connect the negative battery cable.

Hope this helps (remember to rate tna domment this answer).

Apr 09, 2011 | 1999 Dodge Intrepid

4 Answers

Where is alternator located in the engine compartment?


Are these guys SERIOUS??


blueextc3221_1.jpg

The alternator is accessed from UNDER the vehicle LEFT SIDE facing the engine bay.

REMOVAL & INSTALLATION




1. Disconnect the negative battery cable.

2. Loosen, but do not remove the alternator adjusting nut.

3. Turn the front wheels completely to the right, then raise and safely support the vehicle.

4. Unfasten the retainers, then remove the plastic lower splash shield.

5. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.

6. Remove the B+ terminal nut and wire.

7. Loosen the alternator pivot bolt, but do not remove it.

8. Remove the alternator drive belt. The alternator spill shield does not have to be removed.

9. If necessary, remove the bottom pivot bolt and anti-rotation tab.

10. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.

11. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.

12. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.

13. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.

14. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).

15. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.

16. Install the alternator drive belt.

17. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).

18. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).

19. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.

20. Install the splash shield, then carefully lower the vehicle.

21. Tighten the adjusting nut.

22. Connect the negative battery cable. Adjust the alternator belt.

Thanks!!

Feb 07, 2011 | 1998 Dodge Neon

1 Answer

How do you take the alternator off for a 96 plymouth neon


For REMOVAL & INSTALLATION check this procedure...
  1. Disconnect the negative battery cable.
  1. Loosen, but do not remove the alternator adjusting nut.
  1. Turn the front wheels completely to the right, then raise and safely support the vehicle.
  2. Unfasten the retainers, then remove the plastic lower splash shield.
  1. Unfasten the alternator field circuit wiring connector. You must squeeze the locking tab to release it.
  1. Remove the B+ terminal nut and wire.
  1. Loosen the alternator pivot bolt, but do not remove it.
  1. Remove the alternator drive belt. The alternator spill shield does not have to be removed.
  1. If necessary, remove the bottom pivot bolt and anti-rotation tab.
  1. Unfasten the three mounting pivot bracket bolts, then remove the pivot bolt and bracket.
  2. Holding the alternator in one hand, remove the adjustment nut then slide the alternator off the T-bolt. The T-bolt does not have to be removed. Lower the alternator and remove through the wheel well.
To install:
  1. You may need to use a C-clamp to drive the sleeve into the mounting ear for installation clearance.
  2. Position the alternator in the vehicle, sliding it onto the T-bolt. Install the adjusting nut.
  3. Install the bracket and pivot bolt, then install the three mounting pivot bracket bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  4. If removed, install the anti-rotation tab and bottom pivot bolt hand-tight.
  5. Install the alternator drive belt.
  6. Tighten the alternator pivot bolt to 40 ft. lbs. (54 Nm).
  7. Install the B+ terminal wire and nut. Tighten the nut to 75 inch lbs. (9 Nm).
  8. Attach the alternator field circuit wiring connector, making sure the locking tabs are engaged.
  9. Install the splash shield, then carefully lower the vehicle.
  10. Tighten the adjusting nut.
  11. Connect the negative battery cable. Adjust the alternator belt.

Hope helps.

Jul 16, 2010 | 1996 Plymouth Neon

1 Answer

How do i replace an alt on an 97 Grand Voyager?


When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Jul 08, 2010 | 1997 Plymouth Grand Voyager

1 Answer

How to remove alternator from 1997 Chrysler Concorde?


e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1997 Chrysler Concorde

1 Answer

To remove an alternator on a 1998-99 Intrepid, on drivers side


FIRST OF ALL.TURN OFF RADIO SO YOU WONT LOSE RADIO CODE.FOR THE 2.7L ENGINE.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE LOWER PLASTIC SPLASH SHIELD.REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.REMOVE THE LOWER RADIATOR CROSSMEMBER SUPPORT.LOOSEN BUT DO NOT REMOVE.ADJUSTING T BOLT AND THE PIVOT BOLT.LOOSEN DRIVE BELT ADJUSTING BOLT.REMOVE OR DISCONNECT THE FOLLOWING.DRIVE BELT.REMOVE ALTERNATOR ELECTRICAL WIRES.REMOVE PIVOT BOLT CAREFUL NOT TO LOSE THE SPACER.REMOVE THE ALTERNATOR. NOW THE 3.2L AND 3.5L ENGINES REMOVE THE NEGATIVE BATTERY CABLE.THEN REMOVE THE LOWER MOUNTING BOLT AND PIVIT BOLT.REMOVE DRIVE BELTTENSION BOLT THEN DRIVE BELT.REMOVE BRACKET LOWER MOUNTING BOLT AND PIVOT BOLT.THEN REMOVE THE ALTERNATOR + ALTERNATOR FIELD CIRCUIT PLUG + ALTERNATOR B+ TERMINAL NUT AND WIRE.THEN PUT EVERYTHING BACK VISA VERSA.

Sep 18, 2009 | 1999 Dodge Intrepid

1 Answer

Need to install an alternator


Removal & Installation
2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower plastic splash shield
    • Transmission cooler and position it aside
    • Lower radiator crossmember support
  3. Loosen but do not remove:
    • Adjusting “T” bolt and the pivot bolt
    • Drive belt adjusting bolt
  4. Remove or disconnect the following:
    • Drive belt
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire
    • Pivot bolt; be careful not to lose the spacer
    • Alternator 0900c152801d4a1e.jpg
    (The location of the generator/alternator on the 2.7L Engine)
To install:
  1. Install or connect the following:
    • Alternator
    • Pivot bolt with the spacer and leave loose
    • Alternator field circuit plug
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Drive belt
  2. Usinga belt tension gauge, torque the adjusting “T” bolt until the tensiongauge reads 120 lbs. (534 N) for a used belt or 180–200 lbs. (792–880N) for a new belt.
    • Lower radiator crossmember support
    • Transmission cooler
    • Lower plastic splash shield
    • Negative battery cable
  3. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).

--------------------------------------------------------------------------------------------------------------------------------------------------
3.2L And 3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower mounting bolt and pivot bolt
    • Drive belt tension bolt
    • Drive belt
    • Bracket, lower mounting bolt and pivot bolt
    • Alternator
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire 0900c152801d4a1f.jpg
    (The location of the generator/alternator on the 3.2L and 3.5L engines)
To install:
  1. Install or connect the following:
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Alternator field circuit plug
    • Alternator
    • Drive belt
    • Pivot bolt and lower mounting bolt
  2. Usinga belt tension gauge, torque the “V” drive belt until the tension gaugereads 120 lbs. (534 N) for a used belt or 140–160 lbs. (623–711 N) fora new belt.
  3. Using a belt tension gauge, torque the Poly “V”belt until the tension gauge reads 120 lbs. (534 N) for a used belt or180–200 lbs. (792–880 N) for a new belt.
  4. Install the bracket.
  5. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).
  6. Connect the negative battery cable.
Hope this is what you were looking for.

Jan 30, 2009 | 1999 Dodge Intrepid

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
2001 Daewoo Lanos Logo

615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...