Question about Cars & Trucks

Open Question

Require valve clearance specs and head bolt tension for kubota rk70

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Dak408
  • 277 Answers

SOURCE: What are the valve clearances

For a 1999 Vitara the clearance is
intake (cold motor) 0.13 - 0.17 mm
exhaust(cold motor ) 0.23 - 0.27 mm

Head bolts
Apply engine oil to cylinder head bolts and tighten them gradually as follows.
(1) Tighten all bolts to 35 Nm (3.5 kg-m, 25.0 ft. lbs.) according to numerical order in figure.
(2) In the same manner as in (1), tighten them to 55 Nm (5.5 kg-m, 40.0 ft. lbs.).
(3) Loosen ail bolts until tightening torque is reduced to 0 in reverse order of tightening.
(4) In the same manner as in (1), tighten them to 35 Nm (3.5 kg-m, 25.0 ft. lbs.).
(5) In the same manner as in (1) again, tighten them to specified torque.
Tightening Torque (a): 68 Nm (6.8 kg-m, 49.5 ft. lbs.) dak408_3.gif

Good Luck

Posted on Nov 05, 2010

Ad
alicantecoli
  • 22326 Answers

SOURCE: what is the cylinder head tension and valve clearance for a kubota L2002dt

Isnt this a earth moving machine with a big diesel engine ? well if its diesel and it is one of them earth movers then i would need to see the size of the shank on the head bolts and weither its got a turbo but i wouldnt be surprissed to to expect 120 lbs for a turbo diesel with a cast iron head and as for tappets then i would expect around 12th inlet and 14th exhaust would suffice but some industrial engines like this are the same inlet and exhaust like the old thornycroft -be quiet in the wings i know iam showing my age here .

Posted on Feb 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Valve setting in a Kubota zg227z 27 up


This is not a car or a truck and as such I have no real info on the specs you need. If you are going to do your own work you need a service and repair manual.

Oct 01, 2016 | Cars & Trucks

1 Answer

F77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please


Search Results

    F77 2.8 diesel non turbo.1989 model.require head bolt - Fixya

    www.fixya.com/cars/t25792470-f77_2_8_diesel_non_turbo_1989
    Jul 22, 2015 - f77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please - Daihatsu Rocky question. ... Torque to yeild bolts need to be replaced whenever the head comes off.....Long bolts are 46 ft lbs. and ...

Jul 22, 2015 | Daihatsu Rocky Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

Toyota 2kd engine cylinder head tighten tourqe in n-m


Valve clearance is .20mm for the intake and .30mm for the exhaust.
The minimum diameter specs are: 11.6 mm for head bolts, and 12.6 mm for main bearing bolts.

Jul 10, 2013 | Cars & Trucks

1 Answer

Torque setting for 1972 Cororna


My manual shows an 8RC for 70 and 71 and an 18RC for the 72-74

18RC valve clearance HOT IN .008 EX .014 cold spec. .007 .013
Cyl head 72-82 Ft Lbs
Rocker caps 12-17 ft lbs
cam bearing clearance .001-.002
cam endplay .0017-.0066
oil tube 11-16 Ft Lbs

Jun 15, 2013 | Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

There is no nut on the tensioner,just a weird looking thing witch a socket won't fit


Belt tensioner? Usually takes a 3/8 " ratchet or 3/8 " breaker bar to rotate the belt tensioner.
Get in there with an inspection mirror(It's tight quarters!).
Some Toyota's require a skinny wrench to fit onto the 14 mm bolt head.Some are 17 mm.
Socket won't get in there.
Some cars require loosening the engine mount and jack the engine up to gain enough clearance!(Mitsubishi)

Feb 21, 2013 | 2004 Toyota RAV4

1 Answer

Hi, I need to find out the tension on the head bolts of a 1977 Corolla. It has a 3k engine also the clearance in the tappets.


0900c1528004fbee.gif

39-48 Foot pounds (Final torque)-Final torque must be reached in 3 equal stepsRecheck final torque in sequence
The valve clearance HOT, should be exh. .008" and int .006"

May 24, 2011 | Toyota Corolla Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...