Question about Cars & Trucks

Open Question

The power locks on my 1991 chevrolet s10/blazer stopped working, so i want to check the power door lock fuse to see if i can fix it by replacing the fuse but I don't know which one it is on the fuse box. Which is the fuse for the power door locks in the fuse box of my car ? - see picture I took.

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: where is the door lock relay located on a 1999

  • Aux Relay Box #4 is in the rear driver's side removable panel with the tire jack.
  • This Relay box holds the Door Lock / Unlock relays (ice cube type). It also holds the Driver Door Unlock Relay and the ACC Lights Relay (rectangular relays).
  • Posted on Oct 17, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    1991 Chevy Blazer auto door locks stopped working.


    Broken wire inside rubber sleeve between door and body, or switch is bad. You might want to check fuses also.

    Jan 18, 2013 | 1991 Chevrolet S-10 Blazer

    1 Answer

    My mother just passed away and i inherited her 1991 S10 Blazer it only has 60000 miles on it and is in great condition, But the front windows do not go up or down. The back windows work fine. what should i...


    GOD BLESS your mom...On back of fuse door there may be a diagram otherwise pull each fuse & check if good .. then go to door pull out swich & work your way back w/ vom till you have power ,,

    Apr 21, 2011 | 1991 Chevrolet S-10 Blazer

    1 Answer

    1999 Chevrolet Blazer power door locks stopped working how do I fix this?


    Replace fuse and/or relay. Fuse in fuse panel under dash relay in relay panel under hood

    Dec 23, 2010 | 1999 Chevrolet Blazer

    1 Answer

    98 Chev Blazer. power lock problem. driver's door would not unlock doors, now it will not lock doors. passenger side works fine


    you may just have a bad connection under the lock button under switch panel on your drivers door. check electrical plug in at door lock switch by removing that panel from driver door.it may be that you have to replace that door lock switch .thers only one fuse for door locks and if pass side works, it's not blown.

    Aug 19, 2010 | 2001 Chevrolet Blazer

    2 Answers

    1999 S10 Blazer electric door lock butons dont work. What should I check? The fuse in lefthand dash is ok.


    First, replace the door pins and bushings to take the pressure off of the latch and lock actuator assembly. When the door sags and it gets slammed shut, it can break the plastic housing of the actuator and then it doesn't work any more. The latch and lock actuator are all in one assembly. It will need to be replaced after the pins are done.
    And, don't use the door as a crutch when entering or leaving the truck.

    May 24, 2010 | 1999 Chevrolet S-10 Pickup

    1 Answer

    95 S10 blazer 4dr power door locks inop, new battery installed in remote, all fuses good, still inop?


    1. Locate the red two wired programming connector located near the central locking control module that is located behind LH Lower instrument panel. Drop the panel and you will see the red programming connector that is not connected to anything.
    2. Inside the Red programming connector you will see to pins..
    Jump two pins with a section of wire.
    3. System should now lock and unlock doors to indicate vehicle has entered programming mode.
    4. Press any button on keyless remote once. System should now lock and unlock doors indicating the keyless remote has been programmed.
    5. Repeat step 4 to program other remote.
    6. Remove jumper wire from programming connector to exit programming mode.
    7. Test Remote(s)

    Dec 22, 2009 | 1995 Chevrolet Blazer

    1 Answer

    Reprogram keyless entry


    It took me a few attempts to program a new keyless remote for my 2002 Chevy Blazer.
    Insert key into ignition but don' turn it yet. While holding down the UNLOCK switch on the door, the trick is to cycle the ignition ON OFF ON OFF as quickly as possible then release the UNLOCK switch. If done correctly the door locks will cycle 1x to acknowledge. Then hold both the unlock and lock buttons down on the remote for about 15 seconds. The locks should cycle again to confirm...Hope this helps.

    Mar 19, 2009 | 2002 Chevrolet Blazer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    37 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...