Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
fIRST YOU SEE A RUBBER GASKET SURROUNDING THE HEADLIGHT PLUG IN THE BACK OF THE HEADLIGHT ASSEMBLY. pULL OFF THE GASKET AND LET IT HANG ON THE SURROUN DING HEADLIGHT WIRES. tHEN PULL OFF THE HEADLIGHT WIRE HARNESS BY GRABBING THE SOCKET (NOT THE WIRES). AROUND THE BULB IS A THIN SILVER HOLDING SPRING THAT LOOSENS BY SQUEEZING THE ENDS TOGETHER AND ROTATING IT. iT WILL LOOSEN AROUND THE HEADLIGHT. WHEN THIS HAPPENS THE HEADLIGHT WILL "FLOP" AROUND AND PULL IT OUT, REMEMBERING TO SEE HOW THE THREE CONNECTORS ARE LOCATED (I.E - IS ONE CONNECTOR AT 12 O CLOCK POSITION AND THE OTHER TWO ARE AT 9 AND 3 OR ARE THEY AT 3,6 AND 9, ETC.). rE-ASSEMBLY IS THE OPPOSITIE. tHE TRICK IS TO GET THE THIN SPRING WIRE BACK IN PLACE. YOU HAVE TO SQUEEZE THE SPRING AND RE-POSITION IT SO IT KEEPS THE BULB SECURLY IN PLACE
Having just changed the bulb, I would advise taking the whole headlight assembly out first. It is near impossible to feel or imagine how to change the bulb without seeing it. First, use a phillips screwdriver to take the single screw holding the strip off just below the headlight assembly. By doing so, you will now see the other two bottom bolts holding the headlight in. Take all four bolts out then disconnect the bulb from behind. Then proceed as above.
Posted on Jun 14, 2009
Use a wrench to remove the mounting bolt from the underbody through the hole in the splash shield.
Remove the fog light assembly from the bumper by pulling its inner edge first, then the whole assembly out of the bumper.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
Remove the bulb from the fog light assembly by turning it one quarter turn counterclockwise.
Push the electrical connector onto the new bulb.
Turn on the fog lights to test the new bulb.
Reinstall the fog light assembly into the bumper. Tighten the mounting bolt.
Insert the new bulb into the assembly and turn it one-quarter turn clockwise to lock it in place.
Hope this helps you.
Posted on Nov 22, 2009
get under the car and the fog lamps will be on the corners of each side. all you do is twist the electrical connector to the right and it will come out to install one re connect the new bulb and line up the connector and turn to the left to lock it in place
Posted on Apr 03, 2010
remove 2 10mm bolts attaching top of headlight to the radiator support.
remove plastic clip attachinig headlight to top/front of fender.
remove 5 phillips screws on top of grill.
carefully pull out grill enough to remove 1 10mm bolt attaching headlight to radiator support and use slotted screwdriver or prybar to seperate headlight tab from the bracket that goes under the bumper cover.
with a little effort and wiggling pull out headlight assembly.
Posted on Apr 17, 2010
SOURCE: My airbag light stays on-
Check lights such as your SRS (airbag light) have
been on vehicles for 30 years,so you should know
that ANY light on the dash requires retrieving any
codes that may be set & diagnosing from there
That isn't anything many people can do at home
You need a repair shop .
Posted on May 22, 2011
Tips for a great answer:
Oct 14, 2016 | 2004 Lincoln Navigator
Aug 15, 2013 | 2006 Lincoln Zephyr
Jan 03, 2013 | 2006 Lincoln Zephyr
Nov 20, 2012 | 2006 Lincoln Zephyr
Aug 31, 2011 | 2006 Lincoln Zephyr
Nov 22, 2009 | 2006 Honda Odyssey
Nov 07, 2009 | 2006 Lincoln Zephyr
Apr 23, 2009 | 2006 Lincoln Zephyr
129 people viewed this question
Usually answered in minutes!