Question about 1999 Jeep Grand Cherokee

1 Answer

Removal of light lens around licsense plate

I have a 1999 grand cherokee and iam trying to remove marker light lens around licsense plate could you please tell me if it slides off in one direction or you have to pry it off. thankyou michael

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Yes they slide off and has 2 screws each side of them

Posted on Jan 25, 2009

  • Marc Podeszek Jan 27, 2009

    Please rate my response. Thank you !

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Marker lights wont go on


on 1998 and earlier models, the side marker light housing is located next to the headlight housing. Remove the screws and pull out the housing to access the bulbholder on the back of the housing. On 1999 and later models, the park and turn signal bulbs are located in the bottom of headlight housing. Twist the bulbholders out to replace the park or turn signal bulbs. Installation is the reverse of the removal directions.

Apr 04, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Please help my 1999 jeep grand cherokee has been dying out. As soon as I start to slow down or I'm at a red light it wants to die out. When I give it gas its fine but once again when I begin to slow...


sounds like a fuel problem. when was fuel filter changed last! if filter is ok, remove and clean the idle air control it may be sticking. this is what controls idleing, on todays cars. ( IAC ). good-day ! there is another thing you can do. clean out around throttle plate of throttle body and make sure aircleaner is ok. this should help!!

Aug 18, 2011 | 1999 Jeep Grand Cherokee

1 Answer

Describe how to replace side marker light on a 95 jeep grand cherokee loredo


Easy enough, just gently pop off the marker lens, replace the bulb, and press the lens back in.

May 09, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Drivers side headlight bulb replacement


  1. Open the hood to the 1999 Dodge Stratus.

  2. Locate the two headlight lens assembly retaining screws at the top of each side of the assembly.
  3. Remove each screw with the ratchet and a suitable socket.
  4. Place the screwdriver behind the lens assembly to assist in prying out the guide pins that secure and align the headlight assembly. Hold the lens assembly from the outside edge (marker light/directional light section) first and pry from behind with the screwdriver to unseat the guide pins. Pry from the inside end of the lens assembly to unseat the other guide pin.
  5. Pull the lens assembly out far enough to reach behind it and disconnect the headlight bulb wire harness from the back of the bulb. Or simply remove the bulb by twisting the harness and retaining ring counterclockwise and remove it as an assembly.
  6. Turn the marker light/directional light socket and wire counterclockwise to remove it from the headlight lens assembly.
  7. Remove the assembly from the front of the Stratus.

Feb 28, 2011 | 1999 Dodge Stratus

1 Answer

How do i change the front side maker lights on '95 grand chkee?


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Sep 13, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

1 Answer

2004 Jeep Grand Cherokee. Keeps stalling, engine


P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Oct 25, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Changing license plate light


take out the 2 srews that hold the assembly in the hatch and remove it then 1/4 twist the socket to remove from lens assm.

Jul 17, 2009 | 1994 Jeep Grand Cherokee

3 Answers

Replace parking/marker bulb front pass 98 Jeep Grand Cherokee


look in between the marker and headlights its a screw there screw it out

Apr 04, 2009 | 1998 Jeep Grand Cherokee

1 Answer

How to access front turn signal for replacement


Here you go, removal & installation of:

Front Parking/Turn Signal Lights:
  • Remove the screws from the the lens and separate the lens from the bezel
  • Remove the screws from the turn signal housing and pull it out
  • Turn the bulb socket CCW 1/3 turn and remove it
  • Installation is the reverse of this procedure
Side (Front) Marker Lights:
  • Remove the screws from the marker lens
  • Separate the lens from the headlight
  • Pull the bulb from the back of the lens
  • Installation is the reverse of this procedure
Hope this helps

Mike

Jul 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...