Question about 2005 Honda Accord

Open Question

I have an 2005 honda accord and the left turn signal does not work. the right side works fine. the left indicator lamp on the cluster does not come on at all.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 1988 honda accord turn signal

Mine did the same around 200K. Near the hood release handle is the fuse panel with the flasher relay. Remove the panel on the lower dash marked "FUSE" which gives you a viewing window to see the fuse panel which you reach from below the dash to access. Simply place your hand on one of the two 1" wide metal cylinders on the fuse panel(these are the relays) and turn on the left or right blinker. Feel for a click. If you feel a click but it is not constant, YOU FOUND THE DEFECTIVE RELAY!!! (Use the same test to find your Emergency flasher relay) Replace the on that does not work.

Posted on Apr 13, 2009

Ad
bitchn65cuda
  • 70 Answers

SOURCE: directional signal won't turn off

check your hazard switch aka emergency switch. 

Posted on Apr 19, 2009

  • 20 Answers

SOURCE: 1997 honda accord turn signals don't work but fuse is fine

There is a flasher unit in the fuse box. You just pull it out and buy a new one at a parts store. Take the old one with you make sure they are the same.

Posted on May 10, 2009

TimtheStick
  • 83 Answers

SOURCE: Just got a 92 Honda Accord and turn signals do not

A few. First, check the condition of the bulbs, sounds stupid, but it's a first start. Basics first, all else later. After a bulb check, go to fuses. From there, use a digital multi meter and backprobe the bulb sockets to see if you're getting good power/ground at the bulb sockets. If none, back probe further up the wiring. Check all ground connections. If still no power but you have a good ground, go to the combination switch and check output/position on the combination switch. (aka, the "self cancelling trafficator", or turn signal switch) If you're there and havn't found the issue yet, start over. Start at the bulb, head to the switch. If you check everything in between, you'll find it.

Posted on Dec 10, 2009

co7196
  • 3433 Answers

SOURCE: 2004 Accord, left turn signal out, no indicator on

No, no seperate system. Your problem is generally caused by a burned out bulb, bad ground at tail light. A bad flasher would affect both sides. Front and rear must be good. Ck flasher plug in. Good Luck

Posted on May 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My rear turn signals are not working. front turn signals work rear parking lights work brake lights work


In the diagram for rear lamp, the top wires are voltage, the bottom black wire is ground. The brown wire on either side should be tail lamps, goes hot when you turn on the headlamp switch. The other top wire on either should be for turn signal. With everything turned on, is there voltage on that wire?
Because the front works and the rear don't, possible wiring circuit problem? The voltage for turn signals comes from bcm. The bcm knows when you turn on turn signal switch, either side, then the bcm sends voltage to turn signal lamp at the rear and front.

rear-turn-signals-not-working-front-nrw1b5lbo1usuvcsnuvurzx3-3-0.jpg

Oct 17, 2016 | 2009 Chevrolet Chevrolet HHR LS

1 Answer

Fusefor indicators 2008 captiva


Your problem is not a fuse if just the right front isn't working , same for all indicators .
Turn Signal Lamps
The TURN fuse in the fuse block - I/P provides ignition positive voltage to the turn signal relay. The turn signal lamps may only be activated with the ignition switch in the ON position. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal relay output to the turn signal switch assembly. The turn signal relay sends an ON-OFF voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator through the turn signal switch.

an it's not a bad relay , if there is no B+ voltage at the lamp you have an open circuit . You would need a wiring diagram to test circuit from turn lamp back to source voltage to find open . free wiring diagrams at www.bbbind.com . video on youtube testing voltage drop Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Oct 02, 2016 | Chevrolet Captiva Cars & Trucks

1 Answer

I have a 2002 Park Avenue my turn signals do not work my flashers work


gmlogoflat.gifService Information
2002 Buick Park Avenue ' Park Avenue (VIN C) Service Manual ' Body and Accessories ' Lighting Systems ' Description and Operation ' Document ID: 643323


Turn Signal/Cornering Lamps
The HZDT/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal/hazard flasher module and have ground at G202. The turn signal lamps may only be activated with the ignition switch in the ON or ACCY position. The T/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal switch assembly to the turn signal/hazard flasher module. The turn signal/hazard flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators. The left turn signals have ground at G106, G400 and at G402. The right turn signals have ground at G105 and G400. The turn signal switch supplies battery positive voltage to the cornering lamps, the left cornering lamp has ground at G105 and the right cornering lamp has ground at G106.
+snpvvsvwho06+5aqhepgaaaabjru5erkjggg==










2002 Buick Park Avenue ' Park Avenue (VIN C) Service Manual ' Body and Accessories ' Lighting Systems ' Description and Operation ' Document ID: 643323

May 10, 2016 | Cars & Trucks

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

3 Answers

My left turn signal started to only work about 50% of the time, it wont work hardly at all now. the right turn signal is fine. When I try to use the left turn signal, there is no dash indicator lights


Hey Bob how's it going ? I have been looking at Chevy service info for your vehicle and this a little on the complex side or that is the way it sounds from the turn signal description !
Turn Signal Lamps
The smart flasher (GMSF) is an automotive flasher designed to accept turn, hazard, and brake inputs. The GMSF will provide corresponding outputs to the exterior lamps and instrument panel turn signal indicator lamps. This lighting system has dedicated lamps for the turn/hazard functions and dedicated lamps for the brake function. The system incorporates the use of flash rates for diagnostics. The flash rate is a calculation of the number of flashes that occur within a 60 second period. This system uses a percentage of on-time to off-time called duty cycle. For the bulb outage condition, the indicator of the vehicle side on which the outage occurs shall assume bulb outage flash rate mode. The opposite side indicator will assume the normal flash rate mode for an input from the non bulb outage side of the vehicle. Hazard warning lamp outage will maintain a normal flash rate as long as 2 or more exterior signaling lamps are functional. During all modes of operation, the IPC will receive the same flash rates and duty cycles that the exterior lamps receive. The IPC will then control the indicators in the cluster. The vehicle operator will be provided with an audible and visual indication of the flasher operation. Below is a table with flash rates and duty cycles:
Are all your bulbs good ?
Operating Condition
Flash Rate
Duty Cycle
Normal
75 to 105 flashes per minute
45% to 55%
Turn Signal Lamp Outage
2 or 3 times faster than normal flash rate
35% to 55%

Feb 02, 2015 | 2005 Chevrolet TrailBlazer

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

1 Answer

1998 honda accord, with the headlights on the tail lights are on but turn signals do not work. if head lights are off turn signals work unless i apply the brake, if i apply the brake the brake lights work...


It sounds as if you have a bad earth to either one or both of your rear light clusters. If it only happens when you indicate in one direction then that is the offending side.

Nov 20, 2010 | 1998 Honda Accord

1 Answer

My left rear turn signal is out on my 2006 Malibu. The bulb is good, but I replaced it anyway since I had the assembly apart. The left front flasher works fine as well. Before I try and replace any...


Stop lamp an hazard lights work ?
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Repair an open, high resistance, or short to ground in the inoperative turn signal supply voltage circuit. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?

May 16, 2017 | 2006 Chevrolet Malibu

1 Answer

I have a 2003 honda accord, 3.0 6cy. and the left turn signal will not work, but the right side works fine what is the prob.


One of the turn signal light bulbs on exterior of car is burnt out (left side of car).

Apr 21, 2010 | 2003 Honda Accord

1 Answer

Electrical problem


Find the ground wire on one of the lights and add another ground wire to a good clean metal surface and see if that fixes the problem. It defently sounds like a ground problem at one of the lights.

Jan 07, 2009 | 1983 Chevrolet Caprice

Not finding what you are looking for?
2005 Honda Accord Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...