Question about 2006 Pontiac GTO

Open Question

How many labor hours for 2006 Ponitac G6 GTP Oil Pan Gasket

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2006 Pontiac G6-GTP How do I adjust the headlights.

to raise you headlights there is a small brass allen screw located above each headlight under the hood. to raise your headlights turn clockwise until they reach the desired level.

Posted on Oct 23, 2008

  • 1 Answer

SOURCE: 2006 Pontiac G6 GTP window auto close/open

OMG. I replaced the battery in my 06 G6 and had the same problem. the windows would not roll up or down how they did before. I read the answers on here and it does work. Hold up the window switch for ten seconds and it resets. You will have to do it to each window. Worked great. Thanks

Posted on Jan 18, 2010

  • 5 Answers

SOURCE: how much to change a oil pan gasket for 2001 grand prix 3.8 gt

If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Posted on Mar 02, 2010

  • 540 Answers

SOURCE: where is the dip stick located for the

Unfortunately their isn't a dipstick, their is a red cap on top for adding fluid and the way to check it is to have it running up in the air and remove a small plug from the pass side of the trans. after removing the plug with the engine running, add fluid and make sure its dexronVI , to the fill hole until it comes out of the bottom hole and thats how you check and fill it, I know it sucks..

Posted on Mar 18, 2010

kapishtech
  • 2272 Answers

SOURCE: Where is the thermostat located at on a 2006

The thermostat is located on the hose coming from the radiator on the driver side of the eng directly under the intake.Look through your front grill on the drivers side. Check out.Thanks.

Posted on Jul 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 pontiac g6 transmission filter replacement


Remove the transmission pan - some don't have drain plugs, have a big pan underneath to catch the fluid. Pull filter and install filter on. Clean any debris from pan. Install gasket onto pan and install pan back onto transmission. Torque bolts to factory specs. Fill with approved ATF.

Hope this is helpful :-)

-Scott
25449121-csuuapdgb0syz0ddt50mju2i-5-0.jpg
Pontiac G6 GT Trans Fluid and Filter Change time lapse GoPro

Feb 19, 2015 | 2007 Pontiac G6 GTP

1 Answer

Where are the camshaft actuator valves located on a 2006 Pontiac G6 GTP 3.9L V6


I believe you are thinking of the wrong kind of valve. You do not have solenoid valves, you have mechanical valves that open and close off of the lobes of the camshaft.

Aug 23, 2014 | 2006 Pontiac G6 GTP

1 Answer

I have a 2000 grand caravan that i need to gange the oil pan gasket , it is a 3.0 v6 , the transmission is covering the bolts on one end of the pan , i cannot see the bolts let alone get to them , how do i...


I do not have a picture yet, but the labor time to replace this gasket is less than less than 1 hour factory time, and about 1.5 hours chilton time. This is for a 2000 model V6..You are saying that you cannot access all bottom pan bolts?..

Aug 19, 2011 | 2005 Dodge Caravan

1 Answer

How to change a oil pan gasket on a 1998 pontiac grand prix GTP


Make the FixYa experience better for everyone by voting.

Hi,

My name is Ben and I'm your guru, i.e., mentor, an influential teacher or popular expert: a management guru. - origin from Sanskrit, 'weighty, grave' for today.

Removing and replacing an oil pan gasket is a relatively easy task, even for a novice.

Please follow the instructions and you'll have no problem/

  1. Raise the front of the vehicle at least two feet off the ground and support with jack stands.
  2. Drain the oil from the oil pan.
  3. Remove the oil level sensor connector.
  4. Remove the oil pan retaining bolts.
  5. Remove the oil pan.
  6. Remove the oil pan gasket and discard. The gasket CANNOT be reversed.
  7. Clean the oil pan and the cylinder blaock mating surfaces.
  8. Install the new gasket to the oil pan flange.
  9. Replace the bolts and torque to 124 lb. in.
  10. Connect the oil level sensor.
  11. Add the correct amount of oil.
  12. Start the vehicle and check for leaks.

That's the entire process.

Ben

Aug 17, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

How to change oil pan gasket on saturn s seies


to remove the oil pan you have to lower the subframe
it pays about 3.5 labor hours
so if youre not experienced i would advise against DIY

Sep 13, 2010 | 1999 Saturn SL

2 Answers

The dealer wants $1200 for 11 hours of labor to fix the oil leaking from timing cover f crank seal in my 6. does this sound right in any way?


Tha't not right. Dealerstealship charge you for anything. That job cost no more than 200 bucks labor plus gasket.

Jun 17, 2010 | 2004 Mazda 6

1 Answer

Unlocks trunk, but other functions disabled


If you can't live without the key fob and use the old fashion key, I am sorry to say it is time to go visit Mr. Goodwill. Bring lots of money and your first born child for collateral.

Jul 10, 2009 | 2006 Pontiac G6

3 Answers

How much will it cost for a mechanic to change oil pan gasket on my 1998 chevy blazer 4wd big v6 engine?


Gasket = $35 (permatex rubber)
Labor - my manual says 3 hours.
You'll have to be responsible for figuring out the labor price per hour depending on where you are located.
In MI, a garage is about $50/hr, and dealership = $85/hr
CA might be $95/$150/hr.

Parts are minimal on the job - its all labor.
Figure in about $20 for shop supplies... gasket remover, sealant, rags, etc.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Jun 02, 2009 | 1998 Chevrolet Blazer

1 Answer

Leaking gasket of tining belt


do you have a 3.1L V6? The timing cover gasket seals the timing components, it is located behind the belt drive system (alt, a/c, p/s etc.) all of these components must be removed to change this gasket, also the oil pan lower seal gets changed at the same time. The oil pan gasket includes the rear pan seal and the side seals and on for the rear of the pan, the engine must be lifted out of it mounts to change this gasket. It takes time to do these repairs and each shop has an hourly rate per hour on labor. The cost of the parts will be relatively the same at any shop, labor will differ. I hope this helps to answer your questions.

Mar 26, 2009 | 1989 Buick Regal

Not finding what you are looking for?
2006 Pontiac GTO Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...