Question about 2003 Mitsubishi Outlander
Where can I find DIY instructions on replacing the headlight assembly on my 03 Outlander
The 2003 Outlander utilizes replaceable (9007) headlight bulbs. If you're looking to replace the bulb(s);
1. Raise the hood.
2. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. This will allow access to the headlight bulb.
3. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Do not touch the glass of the new bulb.
4. Place the socket back into the assembly, and twist it clockwise. Reattach the plastic cover, and close the hood.
Are you needing DIY instructions for replacing the entire headlamp assembly? Left (driver) or Right (passenger)?
Posted on Jan 18, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: serpentine belt replacement
The routing diagram is under the hood.
Posted on Dec 14, 2008
Hello, to replace the front pads first open the hood and remove the brake fluid cover (will make retracting the piston easier). Next losen the lug nuts till you can turn them by hand than jack up the vehicle and use a jack support stand. Once the vehicle is supported remove the lug nuts and wheel, remove the lower caliper screw and rotate the caliper upward. Remove the old pads, use one of the old pads and place it so it centers the caliper, using a large C-clamp position it with the solid end on the back side of the caliper and rotating handle contact the pad in the center or close as possible. Slowly rotate until the piston is fully retracted into the caliper, your brake fluid may run over but its ok. Install the new pads return the caliper to the normal position over the pads reinstall the lower caliper screw. Put the wheel back on tighten the lug nuts till the wheel is evely and firmly in its normal position. Remove the jack stand lower the vehicle, put the brake fluid cover back on and pump the brakes until they are firm and check the fluid, add some if needed. Tighten the lug nuts, check for leakes. After starting the vehicle pump the brakes a few times, now the fun part the test drive :) allow you self more than normal distance to stop. Tips, I always set the parking brake when working on the front brakes, some people use a 2x4 instead of a brake pad to retract the piston into the caliper, double check your work, i always do and take your time.
Posted on Mar 29, 2010
You have to remove the head light assy from the body,
on almost all vehicles today
Then you can somewhat easily remove the lamp
socket from it & then the lamp/bulb it'self
Have to look for screws or bolts holding it on
May have to remove a few things to get to the
You could look on You Tube--- for Video of it
Posted on Oct 05, 2012
Tips for a great answer:
Dec 07, 2012 | 2007 Mercedes-Benz ML350
Oct 04, 2012 | 2005 Mitsubishi Outlander
Jun 09, 2011 | 2005 Mitsubishi Outlander
Nov 30, 2010 | 2003 Mitsubishi Outlander
Jul 18, 2010 | 2003 Mitsubishi Outlander
Sep 19, 2009 | 2003 Mitsubishi Outlander
Apr 19, 2009 | 1999 Toyota Camry
Mar 28, 2009 | 2004 Mitsubishi Outlander
Jan 06, 2009 | 2003 Mitsubishi Outlander
Dec 31, 2008 | 2003 Honda Civic
487 people viewed this question
Usually answered in minutes!