Question about 2004 Mazda 6

1 Answer

Rear Washer on 2004 Mazda 6

I have a stange problem with the rear washer on a mazda 6. I can hear the motor going but no water is getting through to the rear of the car. I have taken the pipe off the pump and when the washer is on its still the same trickle that comes out. Does this mean that the pumb has gone even though i can hear it??

Posted by on

  • damo79802 Jan 27, 2009

    I thought it might be a blockage as i swapped the pipes on the reservoir and the rear pump came through fine on the front window. Never thought about trying hot water, thanks for the great idea and will let you know how i get on. 
    Thanks mpodeszek!!!!!!

  • damo79802 Feb 01, 2009

    Well after a lot of trial and error, tried the hot water and it didnt work. I then tried (with a bit of modification) a bike pump and i pumped air through the pipe. This did work and some thing must of moved as the air start going through. However i then noticed water coming from under the car by the drivers door. I looked inside by the drivers seat and their was water inside the car, I traced it coming from theright hand side. i took of a couple of panels, the sponge inside was soaking but i cant get to the pipes as they run between the metel skeleton and the body panels. That was pretty much the end of that i believe as there is no way i am removing panels. Is it possible to get this sorted at a garage at all???



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

What you can do is try hot water in reservoir it will loosen the line up and hope fully get the dirt out check the opening at back but keep running until you get most of the water out of the reservoir/ just sounds like you have dirt in the line

Posted on Jan 27, 2009

  • Marc Podeszek Jan 27, 2009

    please rate my response thank you1



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My front wishild fluid dont work read does hoses in hood seem to be dry i hear motor for rear, is rear motor same for front? How can I fix or check it to see where the problem is

Not sure for your car, but some have separate motors for front and rear screens. An old car of mine (can't remember which one as I've had a few) had one motor and it worked one way for the front and reversed for the rear. If you only have the one water bottle for front and rear, it should be easy to see if yo only have the one motor. They generally just push into a hole in the water bottle and held in place with something like an O-ring. If you remove it and get someone to operate it you should be able to work it all out. Make sure your hoses are clear by trying to blow through them and check the jets aren't blocked up either.

Oct 24, 2015 | 2004 Mazda Tribute

1 Answer

Where is the fuse for sunroof on 2004 mazda 6

First result is probably what you're looking for:

Regardless, check each fuse - you can physically see damage in the fuses, so just go through them one at a time, replacing the undamaged ones. When you want to replace one, take it with you and get them to match it at the store.

Aug 30, 2014 | 2004 Mazda 6

1 Answer

2004 Hyundai Elantra GT Windshield Washer Pump Not Working. The FRONT windshield washer works, but when I use the rear washer, I hear nothing but silence. I checked the FUSE, it's OK. What is going on?

You have 2 washer pumps on the washer bottle. You need to check to see if power is getting to the rear pump motor by using a test light. When you press the button, one of the 2 terminals should light up. If it does, the pump could be bad or it may have a bad connection. If there is no power, you may have a bad switch.

Nov 02, 2013 | Hyundai Motor 2002 Elantra

1 Answer

Pump running no water from rear washer wet inside drivers door.mazda tribute

Remove the panel that hides the supply hose and connect the hose back onto the nozzle.

Jul 17, 2012 | 2003 Mazda Tribute

1 Answer

2003 Mazda Tribute front and back washer pumps not working

did you check washer motor alone? find motor and power it with external 12 votls battery or use a cable to power it with your own battery. you need to hear sound. if it creates arcs when you touch wires motor can be burned. if it is burned inside fuse can still be ok. i replaced my washer motor on bmw last week and situation was so.

Nov 19, 2011 | 2003 Mazda Tribute

1 Answer

Not sure how to remove a driveshaft from a 91 ext. cab mazda truck B2600

Welcome to


Remove in the order shown in the figure. Install in the reverse order of removal.

I Image

1. Nut

2. Lock washer

3. Bolt

4. Nut

5. Nut

6. Lock washer

7. Bolt

8. Nut

9. Washer

lo. Nut

11. Lock washer

12. Bolt

13. Rear propeller shaft

Propeller shaft (4x2)

Before removing the propeller shaft, mark the flanges for correct installation.

Propeller shaft (4x4)

Before removing the propeller shaft mark on the front, and rear side flanges for correct


(4x2 Model)

When the propeller shaft is removed from the extension housing, immediately install the

SST into the extension housing to prevent oil leakage

B2200: 490259440

B2600i: 49 5120 440

1m a

Propeller shaft

1. Align the marks. And install the rear propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)

2. Install the center bearing support assembly.

Tightening torque: 36-53 N.m 3.7-5.4 m-kg, 27-39 ft-lb)

3. Align the marks, and install the front propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)

Thank you for using

Regards, Lee Davidian

Nov 05, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

Just changed rear brake pads on 05 mazda 6. now

This is normal and you need to keep pumping the brakes till they reset there self. Once the brake peddle have reset there self and is firm, check the brake fluid level again and add brake fluid if low. After brakes have reset there self, go for a test drive around the block and check the parking brakes. Good luck.

Nov 17, 2009 | 2004 Mazda 6

1 Answer

Blower on my 2004 Mazda 6 went out

Sounds like your blower motor or blower motor resistor went out.

Jan 26, 2009 | 2004 Mazda 6

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides