Question about Nissan Micra
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.
Posted on Sep 14, 2008
You have to remove the wiper arms by prying off the black platic piece over the nut. Remove the nut and the wiper arms. There should be 5 places on the black plastic piece that runs the length of the windshield. Remove 4 of them by prying them out. The one is the middle is a screw. Pull away the plastic piece and you should have access to the mechanism below. I think you need to replace the linkage if it has fallen off.
Posted on Oct 14, 2009
SOURCE: Need to know how to
The wiper cam actuator the cam is made to prevent damage to the
motor by using a spring to allow it to slip if the wipers are stuck or frozen
to the wind shield the spring stretching causes the wipers to stop in the
middle of the window not hard to replace but does require you to do a timing
procedure it should come in the box if not ill give you the basics get the new
part remove both wiper arms careful the windshield is under the black plastic
and I've seen other break the windshield taking the wiper arms off a battery
post puller is the best way to remove , remove the cowl plastic piece you will
see the cam gold/silver in color remove the one torx head screw then install
new one rotate clockwise 2 times should spin freely then spin counter clockwise
should stop look at where it is touching this area should have a 4mm gap the
wiper motor has to be in the intermittent position prior to this turn key on
put wipers in intermittent let motor spin then when it stops shut the key off
then install cam.
Removal Procedure:Tools Required:J 39232 Wiper Linkage Separator
Remove the wiper arms. Refer to Windshield Wiper Arm Replacement .
Remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement .
Remove the water shield.Remove the screw and the nut.
Dissconnect the RH linkage assembly from the LH linkage assembly with the J 39232 .
Remove the LH linkage assembly.Remove the screw from the wiper motor.
Pull the wiper motor free from the slots of the bracket.Disconnect the RH linkage assembly from the wiper motor with the J 39232 .Disconnect the electrical connector from the wiper motor.
Installation Procedure:Tools Required:J 39529 Wiper Linkage Installer
Connect the electrical connector to the wiper motor.Connect the RH linkage assembly to the wiper motor with the J 39529 .
Important: When installing the wiper motor, be sure that the crank arm is in the innerwipe position. The crank arm drive pin must be engaged in the cam pocket.
Install the wiper motor with two locator pads pressed into the slots of the bracket.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
for getting more help on this issue please click on the link directly
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya
Posted on Mar 07, 2010
Tips for a great answer:
Dec 31, 2016 | 2001 Nissan Micra
Jun 15, 2011 | Nissan King Cab Cars & Trucks
Jan 26, 2011 | 1996 Nissan Maxima
Jan 13, 2011 | Nissan Altima Cars & Trucks
Nov 27, 2010 | 1998 Nissan Sentra
Sep 21, 2010 | 2000 Nissan Altima
Oct 03, 2009 | 1997 Nissan.5 Altima
Jun 13, 2009 | 1998 Nissan Sentra
Jul 13, 2008 | 1997 Nissan Sentra
40 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: