Question about Cars & Trucks

Open Question

How to change rear brakes on 2000 Dodge Durango

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 39 Answers

SOURCE: 2000 Dodge Durango

All you need to do is Remove the POSATIVE cable from the battery for about 25 seconds then reconnect it. This will reset the computer and everything else!

Posted on Jan 30, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: Change front brake pads on 2001 dodge durango

Front, remove the hold down clip, should be a 7mm or a 45 torx bit to get the slider pins out. If you are not sure what you are doing, please spend a little money and have a pro do it for your safety, and the safety of others around you.

Posted on Mar 18, 2009

localwonder
  • 6784 Answers

SOURCE: worn brake pads

Front brake pad exchange guide.

Step1 Park the Dodge Durango on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable from the battery. Drain 2/3 of the brake fluid from the master cylinder, using a syringe. Remove the wheel and the tire assemblies. Step2 Compress the caliper piston back into the caliper bore using a large C-clamp to drive the piston into the bore. Use additional force if it is required. Using a 3/8 inch hex wrench or socket remove the caliper mounting bolts. Step3 Rotate the caliper rearward off the rotor and out from its mount. Remove the inboard and outboard brake pads. Remove the spring clip that holds the inboard brakes in the caliper. Tilt the pad out at the top to unseat the clip. Remove the retaining spring that secures it in the caliper. Unseat one spring end and rotate the pad out of the caliper. Step4 Suspend the caliper assembly from the Durango frame using mechanic's wire. Do not allow the caliper assembly to dangle from the brake hose as this may damage the brake hose. Step5 Clean the surfaces of the caliper and steering knuckle with a wire brush. Apply multi-mileage grease or similar product. Using brake fluid or break cleaner clean the caliper slide pins. Apply a light coating of silicone grease to the pins. Step6 Install the inboard brake pad and it's spring. Install the outboard brake pad. Install the caliper over the rotor and seat it in its original position until it is flush. Using a torque wrench, torque the slide caliper pins to 22 ft./lbs. Step7 Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3-4 times to seat the brake pads. Reinstall the wheels. Test drive the Durango at slow to moderate speeds to ensure that the maintenance was performed correctly.
Rear brake pad exchange.

Step1 Lift the Durango off the ground with a car jack. Support the vehicle on all sides with jack stands. Keep children and small animals out of the vicinity when you replace the brakes. Step2 Loosen the lug nuts on the wheels with a torque wrench. Remove the wheel and tire assemblies and set them aside, face up, to prevent damage. Step3 Compress the caliper and remove it by lifting the top up and off the caliper adapter. Hang the caliper from the Durango's frame with mechanical wire. Step4 Remove the inboard and outboard brake shoes from the caliper adapter. Take off the top and bottom anti-rattle springs. Keep the springs separated, as they aren't interchangeable. Step5 Press the piston into the bore with a C-clamp. To prevent damage to the pistons, insert an old brake shoe in between the C-clamp and caliper piston. Remove the C-clamp. Step6 Wipe down the caliper mounting adapter and anti-rattle springs with brake cleaner. Grease the anti-rattle springs with brake grease. Install the bottom anti-rattle springs, followed by the top anti-rattle springs. Step7 Install the inboard brake shoes followed by the outboard brake shoes. Replace the caliper and the wheel and tire assemblies. Lower the vehicle to the ground and pump the brakes to seat the pistons.


Please rate and god bless:)


Posted on Apr 02, 2009

  • 323 Answers

SOURCE: 2001 Dodge Durango SLT 2wd

Inspect the rear brakes for contamination from a possible leaking axle seal.

Posted on Apr 21, 2009

canbruce75
  • 1776 Answers

SOURCE: brake diagram and rear drums diagram for 2001

Visit the autozone.com website and register the car information. It's free and will give you access to an online repair manual for the car. Information regarding the braking system should be available there. It's a handy resource. Hope this helped and best wishes.

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Brake pedal almost going to the floor and fluid coming from the rear on a 2000 Durango


Sounds like you have a leak in the drum brake wheel cylinder. They happen, and more often than you would expect.

You'll see in the pictures, one is the new part and the other shows where it is on your truck.

If the cylinder went bad, you'll see brake fluid leaking, even slightly, out of the rubber boot on either side of the cylinder.
/uploads/images/brake-pedal-almost-going-floor-fluid-35055852-3-1.jpg
/uploads/images/brake-pedal-almost-going-floor-fluid-35055852-3-2.jpg

Feb 23, 2015 | 2000 Dodge Durango

2 Answers

2000 dodge durango abs and brake ligth comes on after driving for a minute


The brake and abs light come on if a problem is detected. When the abs light is on the abs is NOT working. You need to pull the codes from the ecm to detect the problem

Jan 05, 2014 | 2000 Dodge Durango

1 Answer

Grinding rear my 99 dodge durango


What brake you have,maybe need to be change.

Feb 26, 2013 | Cars & Trucks

1 Answer

2002 Durango: 99 durango rear brakes lock up. change perportiona...


Which year is your D,,,, 02 or 1999? In any case, both models have rear drum brakes. The 01 I had would be grabby on the rear shoes when it was damp or humid out for the first stop or two.

May 17, 2010 | 2002 Dodge Durango

1 Answer

2000 durango rear right brake locks up real easy


take the wheel off and see if it isnt wet from leaking oil or brake fluid.

Apr 22, 2010 | 2000 Dodge Durango

1 Answer

2000 Dodge Durango, the emercency brake will not release when disengaged.


The line may need to be replaced if corrosion has built up. I'd would recomend having a shop look into that for you being a saftey issue.

Dec 27, 2009 | 2000 Dodge Durango

1 Answer

2000 dodge durango jerking when stop


Govenor pressure solenoid and transducer fix alot of these.

Sep 16, 2009 | 2000 Dodge Durango

3 Answers

Brake light and ABS light is on and the speedometer, odometer and tripometer are inoperable


replace the left front wheel hub assy. with 4 wheel abs. The spedometer works off of the left front wheel sensor. It will fix the abs/brake light and the spedometer will start working

Jul 23, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...