Question about 1992 Chevrolet S-10 Blazer

1 Answer

I have a blown bulb in my side marker on a 1992

Posted by on

  • shaun renard May 11, 2010

    so what is it you are wanting to know

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

Go ahead and change it. Just go to the part store, tell them that your side marker bulb is blown and they will sell you a new on. Then get your screw driver and go to town.

tepfy

Posted on Feb 27, 2009

6 Suggested Answers

  • 1 Answer

SOURCE: Turn Signal Side Marker Bulb Replacement

I hve the same issue. I have replaced all the bulbs on the fron and back of the left side of the car and still the left front blinker does not blink.

Posted on Nov 05, 2008

  • 5 Answers

SOURCE: headlight bulb replacement & side marker light bulb replacement

i think there are two flat guide pins that hold the headlight assembly in .. just pull them straight up ..and the assembly should come out ..hencse replace the bulbs.

Posted on Jan 25, 2009

  • 9 Answers

SOURCE: replace parking/marker bulb front pass 98 Jeep Grand Cherokee

look in between the marker and headlights its a screw there screw it out

Posted on Apr 05, 2009

rtpflh
  • 546 Answers

SOURCE: Side Marker Bulbs

you need to remove entire assembly to access bulbs.it is secured by small hex head screws & a ''sliding tab'',an L shaped piece you pry up w/a flat screwdriver.

Posted on Sep 20, 2009

c17hydro
  • 2984 Answers

SOURCE: How do I get to the drivers side marker light bulb

  1. Remove the inner wheel well splash shield.
  2. Grasp the bulb socket and rotate it counter-clockwise to remove it from the lamp.
  3. Remove the bulb from the socket.
  4. Installation is the reverse of removal.
b2159df.gif
Remove the retaining bolts for the splash shield and ...

aa616ff.gif
... remove the splash shield from the vehicle

470117c.gif
Twist the bulb socket to remove it from the lamp and ...

61c885a.gif
... lower the socket down to access the bulb

fd06434.gif
Pull the bulb straight out to remove it from the socket

Posted on Oct 10, 2009

Testimonial: "Wow, great pictures! Just what I needed. What book did they come from?"

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What causes blinker to blink real fast


Could be a bad bulb ,plug, wire, or flasher; Check the side marker lights also, some are connected to the turn signal.

Nov 27, 2016 | Cars & Trucks

1 Answer

My 1992 ford ranger driver side tail light wont work but the reverse light does the bulb is good done checked that any suggestions


They are separate bulbs.
are you saying you check both of those bulbs?
if you did, and the taillight/marker light is a good bulb, then it's either the bulb receptacle, or the wiring going to it.

Apr 01, 2015 | 1992 Ford Ranger

2 Answers

Why would only one out of 4 marker lights work?


you are right all marker lights come off of one fuse, inside instrument panel, number 29, a 10 amp fuse my manual does not give a lamp number, it has a chart, head lamps (high) lamp 9005 60 w type a, headlamp (low) 9006 51 w type b, front marker lamps 5w type d, for the rear it says to use a lamp 7443 21.5 w type d, I do not use these, I have special lights on mine, hope that it helps

Mar 28, 2015 | 2007 Scion tC

1 Answer

2002 Mazda Millenia Side marker Lights dont turn on I have replaced both bulbs. What can I do Now?


check fuse and voltage at the fuse and also check voltage at side marker with multi-meter. probable that fuse is blown. if not is it just rears/just fronts or just right or left ones.

May 01, 2011 | 2002 Mazda Millenia

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

2 Answers

Left turn signal is really fast


bad or wrong bulb. all of the bulbs must be good even the side markers if they blink when turn signal is on.

Sep 30, 2010 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

Which fuse do i replace for my side marker light on 2005 silverado??? also half of my radio lights went out, can you help[


If you have just one side marker light out, it's probably a burnt bulb, those side lights are wired in with the parking and head lights, so when either the parking lights or head lights are turned on, the side lights come on also.
As far as the radio, the small bulb in there for the other half is probably blown.

Oct 20, 2009 | 2005 Chevrolet Silverado 1500 2WD

3 Answers

Replace parking/marker bulb front pass 98 Jeep Grand Cherokee


look in between the marker and headlights its a screw there screw it out

Apr 04, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Side marker bulb


i found on the three previous s 10's that i owned it can either be reached from the under neith side or i think it is easier to pull the grill

Jan 25, 2009 | 1992 Chevrolet S-10

1 Answer

Replace side marker bulb


I have the same vehicle and just went through this. The best way to get to those side marker bulbs is to loosen or remove the front grille. There are several screws to remove this grille. I removed the top screws (hood opened you'll see them) and simply loosened the lower and center section screws. This enables you to pull the grille out far enough from the main headlight area, where you can then access the side marker bulb outlet.

Jan 25, 2009 | 1992 Chevrolet S-10 Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Blazer Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...