Question about Ford Focus

Open Question

Ford Focus Front subframe - Focus Ford Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the transmission from a 2005 Ford Focus?


Most newer cars require the whole drive train to be removed and some require for it to be removed from the bottom by removing the front subframe

Feb 14, 2015 | 2005 Ford Focus ZX3

1 Answer

How do you align properly the subframe to the body of 1998 ford windstar .


You will have to obtain a workshop manual it will show the specs. Most panel shops have a rail the chassis is fixed to and the frame can be aligned from that.

Sep 08, 2014 | 1998 Ford Windstar

1 Answer

How to remove 2006 ford focus zx4 manual transmission


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Steering column shaft bolt Battery and tray Air intake assembly Resonator Gearshift cables from the transaxle Gearshift cables from the bracket Hydraulic clutch line from retaining bracket Heated Oxygen Sensors (HO2S) and Catalyst Monitor Sensor (CMS) connections
  3. Support the engine using Special Tools 303-290.
  4. Remove or disconnect the following:
    NOTE Matchmark the subframe to the chassis.


    Rear engine mount and mount bracket Reverse lamp switch Upper transmission to engine bolts Tire and wheels Engine roll restrictor Tie rods from the knuckles Lower control arms from the wheel knuckles Stabilizer bar from the strut Power steering lines from the steering gear
  5. Support the subframe with a suitable lifting device.
  6. Remove the six subframe bolts and lower the subframe from the vehicle.
  7. Remove or disconnect the following:

    Vehicle Speed Sensor (VSS) Right hand halfshaft from the transmission and hang securely aside Left hand halfshaft from the transmission and hang securely aside
  8. Loosen, but do not remove, the starter mounting bolts
  9. Disconnect the clutch hydraulic line.
  10. Secure the transmission to a jack or suitable lifting device.
  11. Remove the 10 transmission-to-engine bolts.
  12. Pull the transmission rearward until the input shaft is clear of the pressure plate, then lower the transmission from the vehicle.

    0996b43f80201168.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Supporting the engine with Engine Support 303-290.

Jan 25, 2011 | 2006 Ford Focus

1 Answer

Need to remove the gear box from a focus 1.6. how to disconect the gear shift linkage


just a pinch bolt ,but you will have to drop the subframe to clear the gearbox

Nov 27, 2010 | 2001 Ford Focus

1 Answer

How ton replace alternator in a 2007 ford focus


you did not state which engine you have but if you are not real handy and/or have experience this is not one you should tackle as your first alternator because...
all will require that you either drop the rear of the subframe or rotate the engine forward to remove the alternator.

everything else is the same...remove the belt, unbolt and remove

about an hour job with experience and two hours if a first time

Apr 03, 2010 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

I have a 2010 ford focus and when I go over a larger bumps at a medium and faster speed I hear a loud clunk in the left front of the car. Under 2000 miles.


take it back to delers it a warrenty job ,i am no doubt wrong here but it could be a monday morning built vehicle and someone has left something lose on the assembly line .From a subframe fixing to the wheel nuts

Dec 08, 2009 | Ford Focus Cars & Trucks

2 Answers

My right subframe would go up when gas is pushed and it shifted hard and i just got a rebuild trns done i changed bot front and back motor mount it helped a lil but my subframe still moves up when i put it...


1. subframe mounts.
2. subframe bolts or nut welded to body broken
3. Body rotted out.
Ford has a bulliten and a retrofit kit to fix this issue.Its a pain in the *** you need to pull up the carpet and drill holes and stuff, I did one way back in the day. Took like 2-3 hours but fixed it. I live in minnesota the road salt eats cars up something fierce!!

Apr 24, 2009 | 1996 Ford Taurus

1 Answer

Do i need to remove trans-axle to install engine


lower subframe its easy to do and drop engine out the bottom onto the floor

Jan 25, 2009 | 2001 Ford Focus

2 Answers

Engine codes 1998 ford taurus


This code indicates that the secondary air injection is not working correctly, you need to have the system tested to see if the electric air injection pump works, this pump is very expensive and you don't want to replace it if the issue is somewhere else in the system electronics, a Ford dealer will have the ness test equip to pinpoint the problem.

Jul 10, 2008 | 1998 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...