Question about 1991 Toyota Tercel

1 Answer

1991 toyota tercel brake lights work rear running lights dont

1991 toyota tercel. The brake lights work fine but when i turn on the high beams there are no rear running lights. Tried changing the lights and the fusses to no avail

Mike

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Sounds like the wiring was repaired and someone tapped into the headlight circuit instead of the parking light circuit

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing front headlight lens on 1985 Toyota Tercel


    How to change a Toyota Tercel headlight lamp - YouTube

    ? 4:06
    www.youtube.com/watch?v=B9dj0o5KIxc
    Apr 22, 2013 - Uploaded by NewEnglandgardening I replaced both headlight lamps on my 1996 Toyota Tercel. ...How To Install Replace Headlight and Bulb Toyota Corolla 98-02... Rear brake shoe replacement Toyota Tercel 1991-1998 Paseo Drum brakes Install Remove ...

Sep 27, 2015 | Toyota Cars & Trucks

1 Answer

I have a problem with the low beams on my headlights. The high beams works just fine. All of the other lights(turn signal, emergency lights, etc.) work except for the low beams.


Check the fuses first. then replace the turn signal switch if all fuses are good. All the lights run threw it, except the high brake light on the rear.

Jan 01, 2015 | 2003 Ford Escape

1 Answer

1991 toyota camry---no low beam lights, high beams working fine


you might have a blown fuse as high & low beam may be on separate fuses, check the fuses in the fuse box under the hood,also wiring for loose connections & check all the connector plugs......hope this helps.....cheers

Aug 04, 2010 | 1991 Toyota Camry

3 Answers

No low beams toyota tercel


Hi,
Check that there is not a relay on the low beam circut, you should find the relay for this in the engine bay area. Also check for a separate mounted relay which may have been fitted to allow larger wattage headlight bulbs to be fitted. I hope this helps, let me know how you get on.

Jason

Apr 04, 2010 | 1991 Toyota Tercel

1 Answer

HIGH BEAM DONT WORK BUT LOW BEAMS DO I HAVE A MONTE CARLO 07 AND I AM WONDERING IF ANYONE HAS THE PROBLEM WHERE THE RUNNING LIGHT WORK BUT THE HIGH BEAMS DONT. iT WORKED FINE THIS MORNING AND WORKS FINE IF...


hiya, it sounds like a problem with either the stalk for the lights high beam or the relay isnt latching properly. id start with the relay as some relays on cars are interchangable. swap one over for another that is the same then try it. if this doesnt work try a new stalk. hope i helped :0)

Jan 28, 2010 | 1996 Toyota Tacoma

2 Answers

Low beams dont work, only high beams do. 02 tacoma


If there is power there, then it has to be the bulbs. The trouble that most people have is, they don't see how both bulbs could burn out at once... and they're right. They don't. But you see vehicles with one headlight all the time. They don't know it unless you tell them or they happen to see it themselves. Then the second light burns out, and they think it's a major catastrophe, when in fact, it's just bulbs. The high beam still works because the bulb is double filament. The only other thing it can be is the dimmer switch, and since you switched it to high, it appears to be working. However, if it's not bulbs, it still could be the switch.

Oct 07, 2009 | 1996 Toyota Tacoma

1 Answer

Center brake light illuminates, but LH/RH brake lights do not


LH/RH lights cable could be disconnected anywhere, will take a long time to trace.
Center Brake Light and LH & RH should be connected at one point.
Jump a cable from Center Brake Light to one of Rear Break Light.
Hope this will works.

Sep 12, 2009 | 1995 Toyota Tercel

1 Answer

High Beam Wire Color? Distinction between three?


with a test light ground connected to the positive battery terminal,,the one that will light up the light is the ground...the other 2 wires are the low and high beam. cut one of those,if the low beam is now on,you cut the high beam wire. if the high beam stays on,you cut the low beam wire.

Jul 22, 2009 | 1991 Toyota Tercel

1 Answer

How can i disconnect the high beams because when i turn my normal lights on the high beams come on. I need to know how I can disconnect them.


there are 3 wires going to each headlamp,a ground,a low beam,and a high beam.. cut the high beam wire, and do both sides .and if you want high beams to work,wire both sides to a single throw double pole switch for the high beams to turn on and off.

Jul 22, 2009 | 1991 Toyota Tercel

Not finding what you are looking for?
1991 Toyota Tercel Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...