Question about 1987 Oldsmobile Cutlass Supreme

Open Question

Can a 83 olds rear bumper fit a 87 cutlass rear end

I neede a bumper on a 87 cutlass can a bumper off a 83 olds cutlass supreme fit the 87 olds

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: 1995 cutlass supreme transmission

It physically will fit and bolt up,but there are many different ratio,and drive and driven sprocket tooth counts,different final drive ratios,all monitored by the computer with electronic speed sensors.If the trans from the 95 has a different ratio than the 93,the computer will set gear ratio error codes,and possibly put the trans in a failsafe mode,stuck in 2nd or 3rd gear.On the transmission case,down by where the passenger side axle would go in,is a thin metallic tag,maybe 2"x 3",and it has bar codes,and also a series of numbers and letters.The numbers and letters,large cap,are the final drive gear ratio code.They should match on the two transmissions in question.

Posted on Jul 31, 2008

cadman000
  • 607 Answers

SOURCE: my 83 cutlass supreme check engine light on

sounds like could be a carb providing an excessive amount of fuel any signs of black smoke from exhaust ), overdue need of spark plugs, or if everything proves ok, a faulty ox sensor

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: I need to replace some dash lights in '87 cutlass supreme

The other screws are behind the woodgrain panels on either side of the speedometer cluster. The panels are held in place with metal clips and are difficult to pry loose. I did it by using a small plastic wedge that I found in a junk pile and once I had a place to start, I worked each corner of both panels until pried out. These panels could break, so go slow and be patient.

Posted on May 03, 2009

66 chrgr
  • 1011 Answers

SOURCE: type of freon used in 1990 olds cutlass supreme. new or old?

This car uses r12 freon that is the old stuff but you can have your system converted over to the 134a.

Posted on Jun 18, 2009

c17hydro
  • 2984 Answers

SOURCE: how do I remove rear brake pads on 94 olds cutlass

Please don't forget to rate! This helps us help you!

1993–96 Vehicles

  1. Remove about 2⁄3 of the brake fluid from the reservoir with a clean syringe or baster type utensil.
  2. Raise and safely support the vehicle.
  3. Matchmark the relationship of the wheel to the axle flange. Remove the wheel and tire assembly.
  4. Reinstall two lug nuts to retain the rotor.
  5. Unfasten the bolt and washer attaching the cable support bracket to the caliper body assembly. It is not necessary to disconnect the parking brake cable from the caliper parking brake lever or disconnect the brake hose unless the caliper is to be completely removed from the vehicle. Freeing the cable support bracket allows enough flexibility in the cable to pivot the caliper up and down and remove the shoe and lining.
  6. Remove the sleeve bolt.
  7. Pivot the caliper body assembly up. Do not completely remove the caliper assembly body.
  8. Remove the outboard and inboard shoe and linings (pads) from the caliper support.
  9. Remove the two pad clips from the caliper support. To install:
  10. Bottom the piston assembly into the caliper bore. Use a suitable spanner-type tool in the piston slot to turn the piston assembly and thread it into the caliper body assembly.
  11. After bottoming the piston, lift the inner edge of the boot next to the piston assembly and press out any trapped air. The boot must lie flat. Make sure the slots in the end of the piston are positioned correctly before pivoting the caliper body assembly down over the shoe and lining in the caliper support. Use a suitable spanner-type tool in the piston slots to turn the piston as necessary. NOTE: Whenever installing new pads, install new pad clips. These should be provided in the disc pad kit.
  12. Install the two pad clips in the caliper support.
  13. Install the outboard and inboard shoe and lining in the caliper support. The wear sensor is on the outboard pad. The sensor is positioned downward at the leading edge of the rotor during forward wheel rotation. Hold the metal shoe edge against the spring end of the clips in the caliper support. Push the shoe in toward the hub, bending the spring ends slightly, and engage the shoe notches with the support abutments.
  14. Pivot the caliper body assembly down over the shoe and lining assembly. Be careful not to damage the piston boot on the inboard. Compress the sleeve boot by hand as the caliper body moves into position to prevent boot damage.
  15. After the caliper body is in position, recheck the installation of the pad clips. If necessary, use a small prytool to re-seat or center the pad clips on the support abutments.
  16. Install the sleeve bolt and tighten to 20 ft. lbs. (27 Nm).
  17. Install the cable support bracket (with the cable attached) with the bolt and washer. Tighten the bolt to 32 ft. lbs. (43 Nm).
  18. Remove the two lug nuts retaining the rotor.
  19. Install the wheel and tire assembly, aligning the marks made during removal.
  20. Carefully lower the vehicle, then firmly depress the brake pedal 3 times to seat the pads against the rotors.

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'96 gm cutlass olds supreme wheel noise


Try rotating the tires and see if the noise follows the tires. If it does problem solved. You need to get a couple of tires.

Aug 23, 2012 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

Tail lights don't work on 83 cutlass supreme


I assume you checked the bulbs and they were good? It's possible that the sockets have gone bad and need replacing. The tail lights are fused through the instrument panel lights. that fuse should be in the middle of your fuse box, marked "instr". If the fuse is good check to see if the dash lights come on when you turn the headlight switch on. If they don't then change the headlight switch. hope this helps.

Mar 12, 2012 | 1983 Oldsmobile Cutlass Supreme

1 Answer

Is a 87 cutlass rear wheel drive ?


Depends on the model. IIRC they were starting to produce some fwd in 87 or 88

May 01, 2010 | 1987 Oldsmobile Cutlass Supreme

1 Answer

Ihave a 83 cutlass olds supreme and the DA PLUG on the alternator have only one wire a red wire, should there be another wire?


a lot of gm vehicles use a single wire alternator the only way to tell is to either look at the back of the alternator or go to a parts store and look at a new alternator for you vehicle

Nov 20, 2009 | 1983 Oldsmobile Cutlass Supreme

2 Answers

My 83 cutlass supreme check engine light on


It means the car is running too rich. Check the air filter. If it clean you will likely need to rebuild the carb if it hasn't been done. If it has you might just need a carb adjustment.

Apr 02, 2009 | 1983 Oldsmobile Cutlass Supreme

2 Answers

'87 Olds Cutlass Supreme Gas Leak


possible thats its where the line hooks to the carburator or the carb itself is leaking

Feb 16, 2009 | 1987 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...