Question about Dodge Durango

1 Answer

Upper trans line how to remove it - Durango Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 937 Answers

Begin Installation Step 1: Test fit each wheel in its final position. Check for proper fit as described below. NOTE: If you only purchased wheels, it is imperative that test fitting is done prior to mounting the tires.......--------------------------------------------------------------------------------------
Auto HID Xenon Light

Posted on Jan 18, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 f150 4x4 with 5.4 litre Front trans seal is leaking do I have to lift the body to remove top trans bolts?


Nope, but you do have to remove both front and rear drive shafts, exhaust Y pipe, transfer case, all wiring that goes to the trans and transfer case, trans fluid lines, starter, torque converter bolts, trans cross member, then the trans and engine should tilt down far enough for you to get to the upper bolts of the bell housing.

Aug 08, 2014 | Cars & Trucks

1 Answer

Radiator replace


remove the upper rad. support housing remove upper and lower rad hoses sometimes your trans cooling lines are in the left side of the radiator you'll need to disconnect these lines don't loose your o-ring for these lines radiator should lift out its a messy job replace all fluids lost after reassembly

Jul 07, 2012 | 1999 Ford Taurus

1 Answer

How do I remove the radiator on my 1995 Pontiac Grand Am?


remove as followed :
1- upper trans cooler line.
2-upper radiator hose.
3-lower trans cooler line.
4-cooling fan electrical connection and retaining bolts .
5-coolig fan.
6-splash guard below lower radiator hose .
7-lower radiator hose from radiator.
8-condenser line retaining clip.
9- condenser to radiator bolts .
10-coolant tank small hose from the radiator .
11-radiator retaining bolts.
12-radiator ....
That's it. feel free to contact me I did this removal more than five times to your grand am type specifically .

Aug 20, 2011 | 1995 Pontiac Grand Am

1 Answer

How to remove starter from 2004 pacifica


REMOVAL
Disconnect the negative battery cable.
Remove (UPPER RADIATOR CROSS MEMBER) and relocate (UPPER RADIATOR CROSS MEMBER REMOVED) the upper radiator crossmember, (Refer to 23 - BODY/EXTERIOR/RADIATOR CROSSMEMBER - REMOVAL).
Remove the radiator fan module (FAN MODULE IN VEHICLE) (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
Remove the wiring harness clip from front mount.
Remove the coolant line clamp bolt (COOLANT LINE BRACKET).
Remove the upper nut from the front mount (FRONT RUBBER MOUNT UPPER NUT).
Remove the upper starter mounting bolt (UPPER STARTER BOLT).
Remove the middle starter bolt (MIDDLE STARTER BOLT).
Raise vehicle and support.
Remove the lower front mount nut (FRONT RUBBER MOUNT IN POSITION).
Raise and support engine (SUPPORT ENGINE).
Remove the lower bracket bolt to transmission (BRACKET TRANS BOLT).
Remove the lower bracket bolt to engine block (BRACKET ENGINE BLOCK BOLT).
Relocate the front mount and bracket.
Disconnect the positive battery cable from starter
Disconnect the solenoid connector from starter.
Remove the lower starter bolt (STARTER LOWER BOLT).
Remove starter from vehicle.

Aug 16, 2011 | 2004 Chrysler Pacifica

1 Answer

Need to change radiator on 2006 ford explorer


THE EASIEST WAY TO REPLACE THIS RADIATOR IS TO REMOVE THE FREON FROM THE AC SYSTEM, DISCONNECT THE LINES GOING TO THE AC CONDENSER, REMOVE THE FAN SHROUD TOP AND BOTTOM, THEN REMOVE THE 13MM BOLTS ON THE UPPER PART OF THE RADIATOR SUPPORTS. REMOVE THE AIR DIFLECTOR ON THE BOTTOM OF THE VEHICLE, REMOVE THE AIR FILTER ASSEMBLY. LAST YOU NEED THE TOOL TO DISCONNECT THE TRANS LINES. ONCE THIS IS DONE THE RADIATOR AND THE CONDENSER WILL COME OUT IN ONE PIECE. AFTER THIS IS DONE YOU CAN EASILY REMOVE THE RADIATOR FROM THE SUPPORT.
IF YOU DO NOT HAVE THE TOOL TO REMOVE THE TRANS LINES YOU CAN UNSCREW THE TRANS LINES FROM THE RADIATOR. YOU WILL HAVE TO REMOVE THE FITTINGS OFF THE NEW RADIATOR AND USE THE OLD ONES. ONCE YOU HAVE THE RADIATOR IN PUT THE FAN SHROUD BACK IN AND TIGHTEN THE BOLTS. THEN IF YOU HAD TO UNSCREW THE TRANS LINES DUE TO NO TOOL, REMOVE ONE OF THE FITTINGS OFF THE NEW RADIATOR AND SCREW THE OLD FIITING BACK IN AND TIGHTEN IT. THEN REMOVE THE OTHER TRANS FITTING AND SCREW IT IN USING THE OLD FITTING. DO NOT REMOVE BOTH OF THE TRANS FIITINGS ON THE NEW RADIATOR AT THE SAME TIME OR YOU WILL LOSE THE RESEVOIR IN THE RADIATOR. ONCE THIS IS ALL DONE EVACUATE THE AC SYSTEM, RECHARGE THE AC, FILL THE RADIATOR WITH COOLANT AND YOU SHOULD BE GOOD TO GO. I HIGHLY RECOMMEND REPLACING THE RADIATOR, THERMOSTAT, AND THE RADIATOR CAP AT THE SAME TIME. I BELIEVE THE THERMOSTATS IN THIS VEHICLE DO NOT OPEN AS DESIGNED WHICH CREATES VERY HIGH PRESSURE IN THE COOLING SYSTEM WHICH CAUSES THE RADIATOR TO FAIL PREMATURELY.
AFTER STARTING THE VEHICLE CHECK THE UPPER RADIATOR HOSE AND MAKE SURE IT IS NOT ROCK HARD, IF YOU DID NOT REPLACE THE THERMOSTAT. IF IT IS ROCK HARD REPLACE THE THERMOSTAT.
THINGS TO CHECK:
CHECK THE RAD/CONDESER SUPPORTS FOR CRACKS YOU MAY FIND THEY ARE BROKEN IF THEY ARE REPLACE THE SUPPORT. IT IS AVAILABLE FROM FORD.

Jan 11, 2011 | 2006 Ford Explorer

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

1 Answer

Instructions on changing the timing cover gasket on a 1991 ford thunderbird with 3.8 liter v6 engine


first you have to diconnect throttle cable and trans kick down from throttle body. than disconnect wires and vacuum hoses and remove upper intake manifold plenum. that should give you access to valve covers . Remove bolts from covers and change gaskets. also replace the gasket on the upper intake plenum. install items in reverse order of removal. keep track of vacuum lines where the go when you remove . mark with tape their location.

Nov 08, 2009 | 1991 Ford Thunderbird

1 Answer

How do i change the radiator in a 2002 ford escort


Remove the radiator fan. Drain the coolant. Disconnect lower hose.Disconnect upper hose. If automatic trans. disconnect trans lines. Remove brackets holding radiator in. Reverse procedure to install new rad. Good luck.

Nov 04, 2009 | 2002 Ford Escort

1 Answer

How do I disconnect the radiator in my 1997 Dodge Dakota pickup. It is an automatic V8 with air conditioning


Drain your coolant (not on the ground), Remove the upper and lower radiator hoses, If trans cooler equiped, remove trans cooer oil lines from radiator, remove either the top sheet metal holding the radiator down, or the four bolts 2 on each side, and lift the radiator out. Good luck.

Jul 02, 2009 | 1997 Dodge Dakota

1 Answer

Oil line


the upper is the in line from the trans cooler the lower is the return line // both screw in to the side of the trans

Feb 20, 2009 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...