Question about 2001 Ford Taurus

1 Answer

How to remove freeze plug 2001 ford tuaras

Freeze plug is under motor mount

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Ford Expert
  • 284 Answers

You have many frost plugs. Some remove from block with an allen wrench, some use a bolt that holds it in, and some are compressed in. Depends on the type of frost plug. If pressed in, use a seal puller or screwdriver/punch with small hammer and pry out. Just don't knock plug into block.

Posted on Jan 18, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the freeze plug that's under the motor mount 09 1994 F250 7.5


Well, I own a 7.5 powered F-250 but I can't remember that particular freeze plug. When you can't pull the motor, you can at least take the rear tranny mount loose and loosen the engine mounts,put a flat board under it so no dents fron the jack you'll be using. You might even have to loosen exhaust bolts,I dunno, and get some space.
THEN what I have done is pry out the bad freeze plug(punch a hole in the center if you can) and then go to NAPA and get an aftermarket bolt-in type plug. I use the rubber EXPANSION type,but I think they make brass ones too.
Check them out! don-ohio

Mar 02, 2017 | Ford F-250 Cars & Trucks

1 Answer

How many freeze plugs are on a 2000 blazer 4.3 vortec


The freeze plugs are spaced out in a straight line along each side of the block. If you see others at the same height in front or behind where the motor mount is, then yes it probably is a freeze plug.

Put a jack under the engine with a block of wood between the oil pan and the jack head. Raise it slightly to remove the motor mount through bolt, then remove the mount from the engine block. Now you should be able to replace the plug. Use a punch to drive in one side, then grip with pliers and pull it out. Clean the recess before installing new plug. Auto stores stock them in all dimensions, or take your old one in for matching up. The rubber expansion plugs work well, too, and easier to install.

Mar 20, 2014 | 2000 Chevrolet Blazer

1 Answer

Replace freeze plugs in 08 Ford F250 Diesel


if you remove the engine mount then you must put a jack under the engine in safe area not to damage sump etc , to get old core plug out carefully drill a hole off centre of it and prise it out , clean and check hole surface , if ok then put sicaflex type glue on new core plug and hit home to same depth the old one came out !

Dec 30, 2013 | 2008 Ford F 250 Super Duty 4WD

2 Answers

Right hand motor mount in way of freeze plug


Jack the engine up,use a jack,and a thick piece of wood,and put it under the crank pulley,remove he pin-bolt from the mount,and jack the engine up,make sure nothing is going to hit at the top,fan,and the rear near firewall,then remove the mount,and the bracket for the mount to access the freeze plug.

Jun 11, 2010 | 1998 Dodge Dakota

1 Answer

Rapid water leak from 1995 Ford F-250


Remove the motor mount for another freeze plug is behind it

May 15, 2010 | 1995 Ford F250

2 Answers

I have a 1996 Ford Explorer and two of the freeze plugs popped out during a freeze. One we were able to get to pretty easily--the other one is somewhere in the middle and looks difficult to get to. Will I...


some times there behind motor mounts and other things you can purchase expadable rubber freeze plugs you might have to lift the motor a little but you shouldn't have to remove the motor unless you popped a freeze plug between the motor and transmision hope this helps

Feb 10, 2010 | 1996 Ford Explorer

1 Answer

I need steps on how to replace a motor for a 2001 ford taurus ses


ooo a fun ford project...well first remove battery, then the hood, go trough and remove all plug ins and any wire attatchments that are attached to the motor, next go through andremove any fuel, power steering, coolant, and A/C lines. the fuel and A/C lines require a special tool, remove the bolts from the exaust flanges underneath the car. take out bellhousing bolts remove the inspection plate from the transmission, remove the tourque converter bolts, remove motor mount bolts, put floor jack under tranny to support it then using a engine hoist (i love my skidsteer) jimmy the motor free from the tranny and slowly pull it out the top, you might have to jack the tranny up and down to allow for clearance for the engine. and of course wen you put the new one in... do all this fun ford stuff backwards

Mar 21, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...