Question about 2000 Ford Crown Victoria

1 Answer

How to install new rearend 1998 crown victoria

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Are you changing the pot or the whole thing?

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4369 Answers

SOURCE: 1998 ford crown victoria fuse box diagram

it should be in your owner manual. if not, I can look up something for you but can't post illustrations to this site.

Posted on Jan 09, 2009

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

emissionwiz
  • 76649 Answers

SOURCE: How do you reset or access keypad of used

u must have the old key pad code to reset the a new code, the code for the keypad is on a paper tag located on the keyless entry module.

Posted on Jun 17, 2009

bigc73542
  • 108 Answers

SOURCE: How are the cylinders numbered on a 1998 ford

Firing order is 1-3-7-2-6-5-4-8 Passenger side of engine starting at front and going back is 1-2-3-4 Driver's side starting at front going back is 5-6-7-8.

Posted on Jul 06, 2009

reisdos
  • 1297 Answers

SOURCE: fuse diagram for 2000 crown victoria

there are 5+ pages of fuses what specifically do you need


Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok i lost the only key with my remote so i bought a new ignition with keys .my boyfriend install it .but it wont start cause the anti theft system wont let it ,on 1998 ford crown victoria ..


It will probably have to be reset to recognize the new key.Try on hooking your battery terminals for a few minutes replace the terminals and try it.If that don't work you may have to take it to the dealership to reset it

Oct 25, 2016 | 1998 Ford Crown Victoria

1 Answer

How to change rear differential in a Ford1994 crown victoria


sounds like a lack of lubrication these rearends used specialized lubricants and most oil change shops do not want to stock a lot of lubricants

Aug 28, 2014 | 1994 Ford Crown Victoria

1 Answer

Where is the fuel pump located?


99 crown vic pump is located in front side of gas tank right behind rearend, jack car up by frame to lower rearend out of the way to gain access to pump.

Dec 31, 2010 | 1999 Ford Crown Victoria

1 Answer

Looking for rearend for ford crown victoria police interceptor


I have one. LBrown1806@juno.com. Selling my 1999 crown vic PI on Unocardealers.com zip code 55057. Please check it out.

Jul 16, 2010 | 1999 Ford Crown Victoria

1 Answer

Changing the heater core on a 1998 Crown Victoria


this job is not for the faint of heart! the dash board must be removed! if you would like to proceed email me and ill guide u the rest of the way

Mar 19, 2010 | 1998 Ford Crown Victoria

1 Answer

How to change a fuel pump on 1998 ford crown


you have to remove the fuel tank- it is located inside the tank

Feb 16, 2010 | 1998 Ford Crown Victoria

1 Answer

Starting 1998 Ford Crown Victoria


try a jump...if still clicking...then replace starter/solenoid together. the solenoid is mounted on the starter.....but they both come when purchasing a new or rebuilt starter .....and a better deal eliminates both problems.....o the starter is located at the flywheel area....GL

Jul 25, 2009 | 1998 Ford Crown Victoria

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...