Question about 2006 Dodge Magnum

1 Answer

Oil pressure switch

Location

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,251 Answers

Here's a picture of it and it's located by oil filter, screwed into block,easy to remove,just remove electrical connector,get wrench and remove.

Posted on Jan 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is oil sending unit located?


You're vehicle has two sensors for the oil,an oil pressure sensor switch & oil pressure sensor.If oil pressure gets below 6psi,the oil pressure sensor switch will turn a dash light on to let you know the pressure is at a dangerously low amount.So if you've got a dash light on,the pressure sensor switch needs to be replaced.Its located to the right of the oil filter housing,on a 2.0 liter.Its located to the left of the oil filter housing,on the 3.0 liter.
If your oil pressure gauge is reading inaccurately,you need to replace the oil pressure sensor instead.Its located near the ac compressor.

Oct 15, 2015 | 2003 Ford Escape

1 Answer

Chevy 350 oil pressure sending unit


The Oil Pressure Switch is located:Under hood, center, rear engine area, driver side of distributor, mounted in block. Here's what it looks like.he oil pressure switch is mounted to the top rear of the engine.

  1. Remove the electrical connector from the switch.
  2. Remove the oil pressure switch.
  3. To install, reverse the removal procedures.

Jul 18, 2013 | Cars & Trucks

1 Answer

Where is the oil sending unit on a 1995 Buick Skylark 3.1 V6?


OIL PRESSURE SWITCH

1995 Buick Skylark 2.3L MFI DOHC Quad 4 4cyl

The Oil Pressure Switch is located:

OIL PRESSURE SWITCH

1995 Buick Skylark 3.1L SFI OHV 6cyl

The Oil Pressure Switch is located: Under hood, center, front engine area, front driver side of engine, mounted in engine block

Jan 05, 2013 | 1995 Buick Skylark

1 Answer

Where is the oil sending switch located on a 2003 dodge durango 4.7


Oil Pressure Sensor

On the 3.7L and 4.7L engines, the oil pressure switch is located at right front of engine just above the oil filter. On the 5.7L engine, the oil pressure switch is located at right front of engine.


hope this helps you

Jan 15, 2011 | 2003 Dodge Durango

2 Answers

Where is the oil pressure sending unit located on a 1999 chrrsler cirrus


There are three engines that come with this car, there are two engines 2.0 and2.4 with the oil pressure switch located on the right front of the engine block, and then if it has the 2.5 engine then the oil pressure switch is located on the leftside of the engine block above the oil filter, good luck,.

Jan 01, 2011 | 1999 Chrysler 300M

1 Answer

I need to know where the oli sending unit is and how to replace it?


zjlimited_305.jpg

Fig. 1: Location of the oil pressure switch-3.3L and 3.8L engines


zjlimited_306.jpg

Fig. 2: Location of the oil pressure switch-3.0L engine


zjlimited_307.jpg

Fig.: Oil pressure switch (sending unit) schematic


The low oil pressure warning lamp will illuminate when the ignition switch is turned to the ON position without the engine running. The lamp also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:

  1. Turn the ignition switch to the ON position.
  2. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
  3. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
  4. With the ignition switch turned to the ON position, check the warning lamp. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.

REMOVAL & INSTALLATION
On the 2.4L engine, the oil pressure switch is located on the side of the engine block facing the firewall. On the 3.0L engine, the oil pressure switch is located on the oil filter adapter housing, next to the starter motor. On the 3.3L and 3.8L engines, the oil pressure switch is located next to the oil filter.
  1. Locate the oil pressure sending unit on the engine.
  2. Disconnect the negative battery cable.
  3. Disconnect the pressure switch electrical harness.
  4. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the pressure switch from the engine.
To install:
  1. Install the pressure switch into the engine and tighten securely.
  2. Attach the electrical connector to the switch.
  3. Connect the negative battery cable.
  4. Start the engine, allow it to reach operating temperature and check for leaks.
  5. Check for proper oil pressure switch operation.

Hope this helps (remember to rate this answerr).



Dec 22, 2010 | 1999 Plymouth Voyager

2 Answers

Oil pressure switch location on 1999 chev cavalier


The oil pressure switch relays the oil pressure in the engine to the instrument cluster. The switch will illuminate the OIL PRESSURE light if the oil pressure drops below 2psi (13 pa). The switch is usually located on the side of the engine, under the intake manifold on the 2.2L engine and on the side of the intake camshaft housing on the 2.3L/2.4L engine.


7fef8ab.jpg

Fig. 1: The oil pressure switch is located on the engine block under the intake manifold and is accessible from underneath the vehicle-2.2L engine

bdee34a.jpg

Fig. 2: Oil pressure switch location-2.3L/2.4L engine


Other, the low oil level switch activates the OIL light in the instrument cluster when the oil level in the pan goes below a certain level. The switch is mounted on the oil pan.


Hope this helped (remember rated this post).

Apr 11, 2010 | 1999 Chevrolet Cavalier

1 Answer

Location of oil pressure switch on a 1997 cadillac deville


Oil pressure switches a normally located by or near the oil filter on all cars. :-)

Dec 24, 2009 | 1997 Cadillac DeVille

2 Answers

I am trying to find a picture that will show me where the Oil Pressure Switch is located


On the 2.4L engine, the oil pressure switch is located on the side of the engine block facing the firewall. On the 3.3L and 3.8L engines, the oil pressure switch is located next to the oil filter.

Good luck, and remember rated this help!!!

Fig. Location of the oil pressure switch-3.3L and 3.8L engines
6bcd90f.gif

Aug 11, 2009 | 2000 Plymouth Voyager

2 Answers

OIl PRESSURE SWITCH


The oil pressure switch is located next to the oil filter

May 20, 2008 | 1998 Buick Park Avenue

Not finding what you are looking for?
2006 Dodge Magnum Logo

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...