Question about 1995 Jeep Grand Cherokee

2 Answers

My 1995 grand cherokee takes a lot to start. turns over fine, but won't fire. checked fuel rail, no pressure. after trying 15 times or so, it will start and run just fine. starts right back up unl

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Jeep Master
  • 2,573 Answers

Four things can cause no pressure in the fuel rail, Faulty fuel pump, faulty fuel return valve , faulty fuel pressure regulator, blocked pickup tube or fuel filter, Try turning the ignition on and off three or four times before starting to prime the fuel system,if this helps suspect the return valve and fuel regulator.

Posted on Jul 05, 2016

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Jeep Master
  • 1,455 Answers

Your Jeep has what's known as the delayed start, no check engine light problem. The Jeep will not start until the check engine light comes on, on the dashboard. Next time it cranks but will not start, look at the dashboard to see if the check engine light is illuminated. If it's not lit up, then your Jeep does have that problem and your Jeep ecu is in need of repair or replacement. There are components inside the ecu that are going bad and will continue to get worse, eventually leading to a permanent no start condition. There are ecu repair services and replacement ecus on ebay.

Posted on Jan 21, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Mikey108
  • 475 Answers

SOURCE: jeep grand cherokee 95 fuel pump takes long time to start ,

First install a fuel pressure tester on the fuel rail and check the pressure during crank. It should be about 30 psi.If the pressure is not good then it could be a bad fuel pump relay or fuel pump itself (in the tank).
If the fuel pump pressure is good then you could have a bad crank sensor.

Posted on Nov 20, 2008

  • 6982 Answers

SOURCE: 1993 JEEP GRAND CHEROKEE LAREDO- TRUCK WONT

OK...I have a 93 outside...one diagram I have shows an ignition module next to coil...but there is none on mine, (4.0 engine)
Two items to check are crank sensor and cam sensor inside distributor. Test procedure can be found in just about any manual including haynes.
You will need a decent volt/ohm meter to do testing. You can also check codes by turning ignition switch on/off three times, leaving it on the third time. Check engine will flash code #'s (ex: one flash, pause two flashes= the number twelve.then followed by a longer pause then another set of flashes etc.)

Posted on Mar 05, 2009

  • 218 Answers

SOURCE: 1995 JEEP GRAND CHEROKEE RAN AND DIED WILL NOT START

IS IT THE 4.0L?IF SO U MAY HAVE A BAD CRANKSHAFT POSITION SENSOR.

Posted on Apr 28, 2009

  • 159 Answers

SOURCE: 2000 Jeep Grand cherokee Laredo

sounds alot the the pcm it controls the fuel pump and ign system but the anti theft would keep it from starting because the key has a transponder in it programmed for that vehicle and that would kill all ign if triggered

Posted on Sep 27, 2009

rickyrt441
  • 4399 Answers

SOURCE: 1999 Jeep Grand Cherokee Laredo

Thanks for choosing FixYa and welcome. If you have a vehicle that will turn over and over but will not start, I will tell you some things that you need to check. Every vehicle needs air, fuel, and fire to start. Now, the first thing you want to check is the fuel system. You want to make sure that the engine is getting fuel. The easiest way to test the fuel system is by testing the fuel pressure on the fuel rail. You need to refer to your owner manual for the correct measurement of pressure. Another easy test is using starter fluid. If it starts when you spray the fluid, you have a fuel issue. If it doesn't, check the ignition system. If your pressure is not correct or you have no way of testing the fuel pressure, start by checking your fuel pump. The fuel pump pumps fuel out of the gas tank and to your fuel filter. When you first turn your key on, you should be able to hear the fuel pump kick on for a second or two. It makes a soft buzzing sound. Listen for this sound. This will determine if the pump is kicking on and working. If you don't hear this sound, check your fuel pump fuse, relay, and your reset button. Not all vehicles have a reset button, so once again check to see if you have this button. If you change all of these and the pump still doesn't work, you may have a bad fuel pump. Test and make sure the pump is getting power before you change it. Now, you want to make sure the fuel filter is not stopped up. Check the gas lines and make sure they have no damage. Lastly, make sure fuel is getting to the fuel injectors. If you are getting fuel, you will need to make sure you are getting fire. You need to test your spark plugs or coils for spark. If you have spark, you should look over your timing belt or timing chain to make sure it is not broken or slipping. If you are not getting spark, you will need to check the spark plugs, coils, coil packs, wires, distributor, distributor cap, and rotor. Anyone of these can cause a vehicle to not spark. Check everything you can. Make sure the rotor is spinning and make sure the distributor cap has all metal contacts. Also, make sure the cap is not damaged or cracked. Make sure none of the plug/coil wires are damaged. Make sure they are all hooked up correctly. Now, it is possible that you could have a bad camshaft sensor or crankshaft sensor. In some vehicles, the camshaft sensor is built into the distributor. You want to test each of these parts and make sure each one is getting power. If a part is not getting power, that may be the reason your vehicle is not starting. If you have a check engine light on, you need to get your computer scanned for error codes. More then likely, if your vehicle won't start, your check engine light is on. The light is on because your computer has detected a problem with the vehicle. You can buy a cheap code reader for around forty dollars from Autozone or Advanced. Just make sure you know all your codes for your vehicle. When you have it scanned, the computer may know the exact parts you need to change. Most of these parts listed run off your ECM. The ignition system is a very complex system. It is rarely, but they do go bad. If you believe that the computer is to blame, make sure you have it flashed before you put it in your vehicle. If you don't, it will not work. Finding your error codes is the best way to finding your solution. If not, you will have many things to check. Always make sure you run a test on a part before changing it. Make sure that part is getting power. If it is not, check the power source. I know this is a lot of information, but any of the parts listed can cause the vehicle to not start. If you have no access to a code reader, fuel pressure tester, or a code reader, you can still check a lot of things. It is just harder. Remember, always use the process of elimination. Determine if the part is working or not and move on to the next part. You will eventually find your problem. Lastly, electrical problems can cause the symptoms you are having. They are very hard to find. When trying to find an electrical problem, you need to make sure you know what to test for. Each wire has a purpose. One part of the engine can shut down another part. You need to know how many volts you are testing for on each wire. You can use a voltage meter to test for current. I hope this helps you and thank you for reading. Thanks for using FixYa and best of luck

Posted on Apr 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Mecury Grand Marquis, sounds like it will turn over but doesn't. Turned over once but wont stay started


Can not nor should you jump a dead battery

You need a good battery or fully charge yours
& then check fuel pressure with a gauge at fuel
rail port

Dec 28, 2012 | 2000 Mercury Grand Marquis

4 Answers

1996 dodge grand caravan 3.3 has spark and gas but won't start??


I had one where the gauge cluster isnt working and van wouldnt start or would start and shut off after 5 seconds so make sure gauges are working

Dec 05, 2012 | 1996 Dodge Grand Caravan

1 Answer

91 Cherokee will crank but won't fire. Replaced


how much is the RPM showing in the datatlogger while cranking?

Dec 03, 2012 | Cars & Trucks

2 Answers

I have a 97 dodge stratus. It won't start. Tried


Make sure it's getting fuel. Try using some ether or starting fluid. If it rumbles to life but doesn't stay running then there's a problem with the fuel delivery system. i.e.... Fuel pump, clogged filter, pressure regulator.... If the ether doesn't change the results you are getting now then it's a fire or sensor problem. Ignition coil, relays, sensors not signaling, PCM... I wish you luck. Let us know how it turns out

Nov 05, 2012 | Cars & Trucks

1 Answer

Last night I stopped my 1994 Jeep grande cherokee v6. Went out this morning and the engine turned over fine but it was as if it was not getting gas or a spark. Similar to when the security system goes into...


When the security system cuts the ignition, it lets you know.
So it was probably the fuel or spark instead.
You need to check rail fuel pressure with a gauge, and check current to coil with test light.
It could be a simple relay like for the fuel pump.
If you got no dash lights, it could be the ignition switch.
The ignition or fuel control module could be bad, but Autozone can check them if you bring them in.

Sep 03, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Im having issues when i try to start mygrand????


This somewhat sounds like a fuel concern.You can crank on it and come back again and it'll fire back up.It might be just taking an elongated time to build up fuel pressure due to a failing pump and once it does build up it fires.An easy way to check this is to go purchase a fuel rail pressure gauge and attach it to the rail, make sure al connections are tight, then crank on the vehicle when it's cold and record down your fuel spec from the gauge.Then do it once again, and record your spec down.If your fuel pump is failing the pressure will either be well below spec or it will be below for the first reading, and then higher on the second reading.Hope I could help!!!

Dec 24, 2009 | 2000 Jeep Grand Cherokee

1 Answer

1994 grand cherokee gives me a hard time starting in the morning no feul in rail ill crank and crank then ill hear the pump turn on and shell start up no drive problems it drive fine only when i try to...


Fuel pump is bleeding back so it isn't holding pressure in the lines. So when it sits long enough it is hard to start. Try turning the key on and then off wait 15 secs or so and turn key on and then off again do this one more time and see if starts. If so then you will need to replace the fuel pump in the tank soon.

Nov 05, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Engine cranks over like normal but will not fire or start


try using starting fluid see if it fires you may have tripped the fuel reset switch see owners manual for location of the switch, disconnect battery for 15 min reset computer this also never hurts to try and will sometimes correct comp errors

Nov 25, 2008 | 1995 Jeep Grand Cherokee

1 Answer

Jeep grand cherokee 95 fuel pump takes long time to start ,


First install a fuel pressure tester on the fuel rail and check the pressure during crank. It should be about 30 psi.If the pressure is not good then it could be a bad fuel pump relay or fuel pump itself (in the tank).
If the fuel pump pressure is good then you could have a bad crank sensor.

Nov 20, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

400 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...