Question about 1996 Jeep Grand Cherokee

1 Answer

Changing electrical cables of grand cherokee limited 4.0 l 1996

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

What do you need; ask and send details if you need 8W Section Electrical Diagrams Repair Manual to send a email.

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: 1994 jeep cherokee linkage

Problem sounds like an internal pressure problem not a cable. If you are able to shift into all gears using the shifter, the linkage is being moved properly. It cannot "come out of gear" by way of the shifter.
In reality, if you were able to manually put the shift lever on the transmission into any particular gear without any shift cable at all attached, it would stay in that selected position forever till you got under there and moved it again. Depending upon what transmission you are using you may have a throttle cable running between the trans and throttle lever on the throttle body...this may have something to do with your problem but would also affect shift points. Any electronic shift controls are also suspect at this point. have it checked by a competent shop. In not being there myself, I can only offer my thoughts on what I would test going into the problem...after testing a better evaluation can be made. Good luck...Hope it's something simple.

Posted on May 19, 2009

  • 323 Answers

SOURCE: Jeep Grand Cherokee Limited P0700 diagnostic problem

P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.

Posted on Jun 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: ELECTRICAL PROBLEMS - NEED WIRING DIAGRAM URGENTLY

ZJ Jeep Grand Cherokeeat 1993 to 1995, so this documents can be help: ZJ-Secc-8W-Wiring-Diagrams

Good luck!!!

Posted on Aug 05, 2009

  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

Clay88
  • 10 Answers

SOURCE: 98 Jeep grand cherokee limited 4.0 auto gearbox shift down

Throttle position sensor

Posted on Nov 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Radiator change 1994 cherokee


    images for Radiator change 1994 cherokee


    More images for Radiator change 1994 cherokee

    Radiator. Replacement - Jeep Cherokee Forum

    www.cherokeeforum.com > Technical Discussion > OEM Cherokee Tech
    Nov 2, 2010 - Jeep Cherokee XJ 1984 to 1996 How to Replace Radiator .... 1994 JeepCherokee 4x4 5 speed 4.0 H.O. flex headers, Flowmaster cat back, ... Changing out lower radiator hose...
    Jul 6, 2011
    Replacing Radiator
    Apr 8, 2011
    RAdiator removal question
    Feb 19, 2011
    Replacing radiator on 1996 Cherokee
    May 19, 2010
    More results from www.cherokeeforum.com

    93 jeep grand cherokee(4.0) radiator needs to be replaced ...

    www.jeepforum.com > ... > ZJ Grand Cherokee Forum

    Sep 23, 2007 - 12 posts - ‎9 authors
    Remove the top radiator bracket and the whole thing will slide out. IF you have .... What I Have: 1994 Grand Cherokee Limited 2.25" 4 Wheel ...

Jan 23, 2016 | 1994 Jeep Grand Cherokee

1 Answer

Will 98 grand cherokee parts fit a 99 grand cherokee


99 models changed and are not compatable with 98 models.

Aug 16, 2012 | Cars & Trucks

1 Answer

Need to find fuse for power windows on 1995 grand jeep cherokee limited


Check position 26 in Passenger Fuse Box...


9_20_2011_5_34_30_pm.jpg

Take off the cover in right side, globe box, early passenger door.

If you need additional details or Electrical Section from Service Manual, contact us: Jeep Grand Cherokee Service Manual

Good luck.

Sep 08, 2011 | 1995 Jeep Grand Cherokee

1 Answer

1995 grand cherokee limited edition. I had to


Look for the electrical plung switch which is usually at the front hood corners. Trace the wire back towards the latch.

Nov 19, 2009 | 1995 Jeep Grand Cherokee

1 Answer

1996 Jeep Grand Cherokee window relay


Check in the Fuse Block, the cavity 2, fuse 30 Amp c/Brkr (Section (8W Page 7)

More details about electrical system for ZJ Grand Cherokee, you can find here: ZJ-Secc-8W-Wiring-Diagrams

I hope help you with this (rated this help). Good luck.

Sep 24, 2009 | 1996 Jeep Grand Cherokee

1 Answer

'03 Grand cherokee limited 4x4 4.7L. I am hearing


pull belt off and turn pulleys until u find bad one. first start jeep with belt off and make sure its not in motor. check power steering fluid. dont leave motor running for 2 long with belt off

Aug 12, 2009 | 2001 Jeep Grand Cherokee

1 Answer

ELECTRICAL PROBLEMS - NEED WIRING DIAGRAM URGENTLY


ZJ Jeep Grand Cherokeeat 1993 to 1995, so this documents can be help: ZJ-Secc-8W-Wiring-Diagrams

Good luck!!!

May 05, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Blower Motor Power Cable/Connector Fried


A Used Parts Yard would Have toe Whole Shooting Match and THIS IS WHAT I WOULD ADVISE AS the Power Core Fried for a reason power distribution module and all. Unless you Wish to Purchased all New ORDERED From DEALER

Jan 12, 2009 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...