Question about Cars & Trucks

Open Question

HOW TO CHANGE WHEELS ON A ROAN KORTINA - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change steering wheel angle how to change steering wheel angle to chrysler voyager 2003o chrysler voyager 2003


dont try removing the steering wheel as the airbag will cause this to be a problem , adjust the tracking until the wheel is in the position you want , make sure you adjust the track rods equally on each side , this is a little bit of trial and error if your doing it your self ,

Jun 25, 2016 | 2003 Chrysler Voyager

1 Answer

What is a wheel bearing and where is it located?


The wheel bearing is the bearing that the wheel spins on the axle when the wheel turns. If its a newer car you may have to change the whole wheel assembly as they don't change just the bearings any more. On the real old cars I used to do it myself but no more.

Mar 17, 2015 | Hyundai Accent Cars & Trucks

1 Answer

How to change rear wheel bearings


25317835-3udur2h4av2xrpdnawrm5shi-5-0.jpegRemove wheel,brake caliper & bracket,disconnect speed sensor & remove hub wheel bolts (Wheel bearing/hub is an assembly)

Dec 11, 2014 | 2004 Mini Cooper

2 Answers

Front wheels make a whirring sound Is this a wheel bearing or could it be c v joint


if it changes when turning right or left it is a wheel bearing if noise does not change when turning try rotating tires from front to rear and see if it goes away as it may just be tire noise

Sep 18, 2014 | 2009 Chevrolet Cobalt

1 Answer

I have a 1994 Ford Bronco Xlt with a 302 V8 Automatic.. When the truck was on a lift the front passenger side wheel had alot of negative camber I believe.. The wheel was slanted like this \ . The stearing...


To check the joints jack the wheel off the ground by the lower control arm and putting one hand on the top of the wheel and the other on the bottom try moving the wheel in and out. If you can then one or both ball joints are bad. Have someone move the wheel and watch the joints you will see if one or both are bad. While the wheel is off the ground move the wheel from side to side, that will tell you if you have bad steering linkage. You don't have to hold the steering wheel straight when changing the joints. But you will need an alignment when your done. Note; When installing the new parts try to get them as close to up and down as you can. Also if you change the tie-rods count the turns and install the new tie-rods to the same turns.

Apr 12, 2013 | Cars & Trucks

1 Answer

Brake light stays on change everything b ut the left wheel sensor mech hook his reader to my truck and code said left front wheel


well if you changed everything but the left wheel sensor and the mech has code of left wheel , ................................................... what should you do? the mech didn't say? I guess i'd change the left sensor!

Jan 16, 2011 | Dodge Durango Cars & Trucks

1 Answer

My truck sounds like its roaning when i drive


CHECK AND SEE IF THE FAN CLUTCH IS BAD SHUT OFF ENGINE AND OPEN HOOD GRAB THE FAN BLADE AND SEE IF IT TURN FREE OR HARD ALSO CHECK AND SEE IF IT HAS MOVEMENT BACK AND FORTH

Oct 16, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How often to change the engine oil for the kia sephia (b5 engine)


you have to change the engine oil for every 5000 to 10,000 kms. every 5000 kms you can change the rotation of wheel ( changing front to back and back to front wheel.) this wheel changing procedure is given on yours cars users manual.

Sep 12, 2009 | Kia Sephia Cars & Trucks

2 Answers

Fly wheel needs to be replaced


Yes you do. If it's 4x4, i find it easier to pull the motor.

May 04, 2009 | 1989 GMC Sierra

1 Answer

1998 mustang squeaking wheel bearing


The wheel bearing need to change.
Grease will only cover the problem for a little while.
If you jack the wheel up a little off the pavement.Then try to shake the wheel back and froward. If it shake then the wheeling bearing is getting bad. There suppose to be no shake on the wheel.

Mar 19, 2009 | 1998 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...