Question about Cars & Trucks

1 Answer

Replaced a evaporator emission canister, and tried to reset so that the light would go off and it would for a little while and come back on need help for the correct code

Replaced a emission canister on my 2008 Mitsubishi endeavor, and still can't get the light to stay off tried to reset it and it goes out for a while and comes back on. would like the correct code the dealer did the diagnostic test and said that this needed to be replaced and that is what was done.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Correct code ??
The code probably said there was a problem with the function of the evap system, but not that a part needed to be replaced.
Since the actual problem has not been fixed, the warning light continues to come on.
If the dealer replaced the canister you should have them refund your money for the part and try again.

Posted on Jan 17, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 651 Answers

SOURCE: check engine light/2003 toyota CE

have you had a diagnostic code check? if not i'd start there. it sounds like it might be a oygen sensor, but before spending money on it, it really should have a diagnostic test to tell you exactly whats causing the problem.

Posted on Nov 28, 2008

freetek
  • 5568 Answers

SOURCE: Evaporative emission system - small leak/no BB flow condition

Although I recommend you buy a Haynes service manual for your Dodge, I think you will find the canister attached to the firewall or one of the fender wells. Most of them look a lot like an overgrown spam can and it will have two connections on it.

Posted on Mar 06, 2009

motor1258
  • 6674 Answers

SOURCE: OBD codes 442 & 455

Check all of your EVAP lines and the charcoal canister. Also check the lines and overflow line from the gas cap to the gas tank.

Posted on Jun 12, 2009

  • 7353 Answers

SOURCE: 2001 Alero code p0440.

there is still a small leak, the shop thats doing the testing can repair it? right? Usually these things are just one item, you may have more than one.

Posted on Sep 28, 2009

  • 11147 Answers

SOURCE: Evaporative Emission System codes

check ur gas cap for tight and proper seal that is the most common problem for the the evap codes if cap is good check fuel and vent lines for damage or leaks from gas cap under vehicle up to engine compartment

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emissions Code


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Purge control VSV connector disconnected.
- Evaporative Emission (EVAP) Canister Purge Regulator Valve is faulty/jammed.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
- Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve.
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Jan 10, 2014 | Toyota Cars & Trucks

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

2 Answers

Trying to put a new vapor canister in 95 grand Marquis.I got two lines running from engine to plug into canister but my connection has two plugs for my lines but on canister still a open hole nothing to...


Section 03-13: Evaporative Emissions 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual DESCRIPTION AND OPERATION Evaporative Emission Canister Fuel vapor emitted through the evaporative emission valve (9B593) is stored in two evaporative emissions canisters (EVAP canister) (9D653) . I think you should have 2 engine vacuum lines, one for each canister.


Evaporative Emission Canister Purge Valve
snorkelbobby_88.gif

---------------------------------------------------------------
Evaporative Emission Tube Shut Off Valve The evaporative emission tube shut off valve (9G332) is located in-line between the evaporative emission valve (9B593) and the evaporative emissions canister (EVAP canister) (9D653) . The evaporative emission tube shut off valve control valve is mounted on the fuel tank (9002) by an integral bracket. The evaporative emission tube shut off valve closes the flow path from the evaporative emission valve to the evaporative emissions canister during refueling to prevent overfilling of the fuel tank .

Evaporative Emission Tube Shut Off Valve snorkelbobby_89.gif

Aug 28, 2011 | 1995 Mercury Grand Marquis

1 Answer

1996 Ford Aerostar 3.0 L V-6 Constant check engine light ON Ran codes. Code says vacuum leak on fuel canister. I'd like to change all the vacuum lines. Don't have a good schematic. Haynes manual only...


what codes?

The vacuum lines run from the canister to the intake manifold. One is the purge hose to deliver stored fuel vapor to the intake to be burnd when engine is warm and you are crusing at part throttle. The other line is the vacuum line to operate it.

Fuel Vapor Valve, Aerostar (4.0L Engine) The evaporative emission valve (9B593) uses a small orifice, 1.83mm (0.072 inch), that allows vapors to pass into the vapor line running forward to the evaporative emissions canister (EVAP canister) (9D653). This evaporative emission valve mounts directly into the fuel tank (9002) using a fuel vapor separator seal. Fuel vapors trapped in the sealed fuel tank are vented through the orificed evaporative emission valve. The vapors from the fuel tank leave the evaporative emission valve through a single vapor line and continue to the evaporative emissions canister in the engine compartment for storage.
-----------------------------------------------------
Fuel Vapor Canister Purge Regulator Valve, Aerostar, Ranger Removal and Installation
  1. Disconnect wire harness from evaporative emission canister purge valve (EVAP canister purge valve) (9C915).
  1. Disconnect wire harness from thermistor.
  1. Disconnect evaporative emission canister purge valve assembly from fuel vapor canister and throttle body.
  1. To install, reverse removal procedure.
-----------------------------------------------------------------

snorkelbobby_48.gif

Mar 25, 2011 | Ford Aerostar Cars & Trucks

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Check Engine lite comes on Code PO440


16824/P0440/001088 - EVAP Emission Control Sys: Malfunction Possible Symptoms
  • Malfunction Indicator Light (MIL) active
Possible Causes
  • Evaporative Emission (EVAP) System leaking
  • Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80) faulty
  • Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115) faulty
Possible Solutions
  • Check Evaporative Emission (EVAP) System Sealing
  • Check Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80)
  • Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115)

Jun 17, 2010 | 2000 Volkswagen Beetle

1 Answer

The check engine light is on and the code is p0457


P0457 Evaporative Emission Control System Leak Detected. The Evaporative Emission Control System EVAP is designed to trap and store fuel that evaporates from the fuel tank, throttle body and intake manifold taht would normally enter the atmosphere. Fuel vapors are transferred from the tank and throttle body to a canister where theyre stored when the engine isnt running. When the engine is running, these vapors are used in combutions so every little bit of gas is used.

Poor Idle, stalling, and poor driveablility can be caused by an inoperative valve, damadged canister, split hoses, or hoses connected to the wrong place. Check the fuel cap for damage. Inspect each hose attached to the canister for leaks/cracks. Look for fuel leaking from the bottom of the canister as well. I hope this will help you.

Apr 10, 2010 | 2003 Ford Escape

2 Answers

Where is the evaporative fuel solenoid on a 1998 sw2 saturn? i have 2 monitors that with not reset on is the solenoid and the other evap system. i have already changed the gas cap. i do not have a service...


Evaporative Emission (EVAP) Canister Purge Soleno Evaporative Emission (EVAP) Canister Purge Solenoid Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.
id Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.

Oct 07, 2009 | 1998 Saturn SC

1 Answer

I have engine light on and code 1457 on 1999 Odyssey.Please help!!!!!!!!!


That code is "evaporative emission control system leakage. (evap. canister system)"

this code takes at least two drive cycles to set. You can try to reset the engine light and emission computer and clear the code and see if the code resets. If it stays clear, it was probably a spurious code. To reset the engine light and emission computer, pull the No. 13 "clock/backup" (7.5A) fuse in the front passenger's kick panel fuse box. Wait at least 10 seconds. Put the fuse back in. This should put the check engine light out. If the light comes back on after two drive cycles (that is; start, run for a while, turn off X 2) have it checked out by a mechanic.

Jul 22, 2009 | Honda Odyssey Cars & Trucks

2 Answers

P0441 EVAP Control System Incorrect Purge Flow


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

Jun 15, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...