Question about 2005 Chevrolet Silverado

Open Question

2005 chevy silverado abs line diagram

Brake line diagram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ewashmidas
  • 362 Answers

SOURCE: 2005 CHEVY +TRAIL BLAZER ABS AND BRAKE LIGHTS ON

When the ABS light is on when driving there is a problem in the anti lock brake system and you will need to have it tested to find out what the problem is. As long as the light is on the ABS has been shut off by the computer until it is repaired. There could be problems with one of the wheel speed sensors, wiring or the ABS pump. On some vehicles the red brake light will come on too.

Posted on Jan 28, 2009

Auto Master
  • 139 Answers

SOURCE: 00 Chevy Silverado... ABS EBCM diagram help??? Brake line hookups

Hello,
I hope this helps.






1ec2f93.jpg
Thank You,
Roy

Posted on Aug 28, 2009

  • 400 Answers

SOURCE: abs codes co281 & co265

the first of the two codes is for the brake light switch, the one that is under the dash attached to the brake rod and brake peddle. Not much to diag on that one, if its bad it's bad, and when it sets the code that means it's bad.
The second one is for the abs modual, it's under the truck on the drivers side. It is bolted to the top of the thing that has all of the brake lines going to it. MOST all of the time that code is set the modual is bad. It can be a little hard to get the bolts out they are torqs 20 or 25(i'm getting old). There are four of them holding down the modual. There are also a couple of connectors going to it. And some of the time it will blow the fuse for the abs under the hood(its in the underhood fues block). Make sure to clean off the modual before you pull it out. You don't want dirt getting in the solinoids for the BPMV(that's the thing it's bolted to).

Posted on Oct 20, 2009

  • 99 Answers

SOURCE: i need a diagram of rear drum brake assembly of a

Haynes manual should have a breakdown. They run about $20 at the parts store.

Posted on Oct 26, 2009

emissionwiz
  • 75822 Answers

SOURCE: can't get brake fluid from abs into lines after

I read this same problem all the time, the reason u can't bleed the lines is that a special tool is required that pluge into the ABS and holds the hydraulic valves in the ABS control open for bleeding, there is no way around this.

Posted on May 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?


First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

1 Answer

Where is abs module on a 2005 chevy silverado


To the left of the master cylinder. Some are on the right side. a lot of steel lines going to it. OOPS,wrong answer.
The ABS module is located in the frame rail on the drivers side of your truck about middle way of the driver front door. It has about 5 brake lines going in the front of it and has 2 bolts or so holding it on the frame with a bracket. You can change it yourself but you will need help bleeding your brakes and it can be a PITA to get all the air out of the system.
Don't do it.

Nov 11, 2014 | Cars & Trucks

2 Answers

Brake line on chevy silverado broken,need diagram to follow line back to box in middle of truck


Brake line diagrams dont exist like wiring diagrams do. If your truck has ABS, that's the ABS controller, and if not it's just the proportioning/metering valve.

Apr 27, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 2005 chevy 1500 silverado abs lights came on but brakes feel good a little quick maybe . Please help


maybe you need to check the brakes physically
and also get some brake cleaner and spray on the pads
might do the trick

Dec 05, 2010 | 2005 Chevrolet Silverado

3 Answers

Can't get brake fluid from abs into lines after installing new brake line on a 2000 chevy silverado


I read this same problem all the time, the reason u can't bleed the lines is that a special tool is required that pluge into the ABS and holds the hydraulic valves in the ABS control open for bleeding, there is no way around this.

May 19, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Truck not stoping and anti brake is working.


dosen't stop at all or just slow?, if the abs is working then you should feel the pulseing in the brake pedal just before tire lock-up, the tires will not lock-up with abs fully funtioning unless all four tires or two are in lock-up depending on the abs application, if abs fails it reverts it self to regular braking ability, hope this helps

Sep 14, 2009 | 2004 Chevrolet Silverado

1 Answer

ABS light keeps coming on after replacing the rear brakes


make sure abs sensor not broken or damaged, also double check fluid level ? may need to get it scanned for codes to tell you fast whats the problem?

Aug 26, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Remove service brake system display from dashboard?


Check ABS system for codes. I have an '03 Silverado and have a faulty EBCM( Electronic Brake Control Module, "ABS module"). Can't reset anything. Only replacement of EBCM will fix it. Incidentally, if you have to replace it, you can check on Ebay for a rebuilt unit. You shouldn't have an issue with your "base" braking system though, if this is the case. ABS is electronically controlled and with or without it, your brakes will still function. I hope this helps.

Nov 12, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
2005 Chevrolet Silverado Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...