Question about Cars & Trucks

1 Answer

My 1991 ford ranger wont disengage out 4x4 hi

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

With the transmission in neutral,and on level ground try rocking the truck back and forth manually while working the shifterfor the 4 wheel..sometimes if too much pressure is mechanically on the drivetrain it will not shift at all..also check fluid lever in transfer case..low fluid will cause the shifter to bind up..good luck..

Posted on Jan 17, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

Xtremeroofin
  • 67 Answers

SOURCE: 2003 Ford Explore 4x4 stuck in 4x4 Low

Try backing up in 4x4 then put it in N and shift out of 4x4

Posted on Dec 22, 2008

junkman1249
  • 552 Answers

SOURCE: hi there,i need to get a copy of Ford Ranger 2007

check out rockauto.com

Posted on Mar 29, 2009

cadman000
  • 607 Answers

SOURCE: 1991 ford ranger wont start

I do believe the FORD is located under ther hood either on the firewall or on L/S wheel housing. Have encountered many , many faulty control modules. There came a time if you came across a Ford product with a no start, you automatically suspected it, and 90% of the time you were right.

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 ford ranger 4wd wont disengage


Usually the 4x4 shift motor mounted on the transfer case. Very rare anything else goes bad on the trucks

Aug 10, 2014 | Ford Ranger Cars & Trucks

3 Answers

Wont disengage out of 4 wheel drive 1998 ford ranger first time its stuck in 4 low we have backed up turned switch numerous times shut it off and restarted


Be sure to put the truck in neutral, while engine is running, while you disengage from 4 wheel drive (low) to 4 wheel drive (high) and then finally to 2 wheel drive. It is critical to shift transmission into neutral when switching out of 4WD Low, as indicated in your owner's manual. Hopefully, this will help to FixYa problem!

Oct 14, 2010 | 1998 Ford Ranger SuperCab

1 Answer

I have a 1991 ford ranger xlt 4x4 I went to the ford dealer they put it on there computor they cant find the problem they cant even acsess the comp on my truck idels rough and no overdrive can someone help...


transmission modulator valve is clogged. it will not show up on the computer,but will definately make your truck do what its doing. 88-94 rangers hav had technical service bulletins issued by Ford for this issue. Very easy to replace.

Apr 29, 2010 | 1991 Ford Ranger Supercab

1 Answer

Clunging when in 4x4 . takes awhile to disengage


hi aro trtosdkutia tar otiuaeritrtuiah a topure t

Aug 07, 2009 | 1993 Ford Ranger SuperCab

1 Answer

How to tell if 91 ford ranger 4x4 4wd button on


With the truck runing in park. Look to see if a light is on at the shifter or on the dash. Put it in L2 and take off it it lurges it is in 4X4.

Jun 05, 2009 | 1991 Ford Ranger Supercab

2 Answers

4 wheel drive


if its push button 4x4 you can be in nuetral or drive and not to exceed 40mph in 4 hi and u dont need to put it in reverse

Jan 10, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...