Question about 1997 Oldsmobile Cutlass Supreme

Open Question

How to remove widow wiper arm 1997 oldsmobile cutlass

How to remove

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: how do I remove the windshield wiper arm from a

most car parts stores will do it for you and you can watch

Posted on Oct 21, 2009

Ad
agent91
  • 2100 Answers

SOURCE: How do you remove the wiper arm on a 96 olds

It is just froze up, a tap with a rubber hammer should loosen it, Or try to pry it gently from side to side, Maybe some Blaster, and put the nut back on to protect the threads, and tap on the nut.

Posted on Feb 15, 2010

  • 9 Answers

SOURCE: turned my wipers on in 1980 oldsmobile cutlass only one arm moved

Take your car to AutoZone and tell them. It is either the windshield wiper motor or a small plastic piece that connects the arm to the motor broke. I am leaning toward the plastic piece being broken, it is really inexpensive to fix. The people at AutoZone will be able to check it and tell you exactly hat is wrong. WARNING: watch them and what they do. some people are not as honest as others.

Posted on Mar 08, 2010

  • 2002 Answers

SOURCE: what tools are required to

You need a ,large adjustable wrench,a 9/16 wrench, a hammer, and a pitman arm puller. It is a special tool that you may be able to rent but will probably have to buy (about $60). With the latge nut removed you put the puller on the old pitman arm and tighten it. When it is tight hit the center tightening bolt with the hammer and tighten again. Repeat until the arm comes off.
If you try to do it without the puller you will wreck the seal in the bottom of the steering box and it will leak. Replacing the seal will require removing the pitman arm again. hope this helps.

Posted on Mar 20, 2011

  • 878 Answers

SOURCE: Car was stolen, when received

take small cover of wiper arm underneath is nut loosen and pry wiper arm off good luck

Posted on Sep 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

Want to change fan on blower heater


Removal

  1. Remove wiper arms.
  2. Remove cowl panel.
  3. Disconnect blower motor electrical connector and vent tube.
  4. Remove blower motor retaining screws.


  1. Remove fan retaining nut from blower shaft through plenum opening while holding the fan from the engine compartment.
  2. Remove fan from blower motor while removing blower motor from vehicle.
Installation

  1. Hold fan through plenum opening.
  2. Install blower motor to vehicle while installing fan to blower motor.
  3. Install fan retaining nut to blower motor shaft through plenum opening.
  4. Install blower motor retaining screws.
  5. Connect electrical connector and vent tube.
  6. Install cowl panel.
  7. Install wiper arms.

Aug 13, 2013 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Windshield wiper doesn't come all the way up.


Your wiper arms are loose at the base. Loosen the nuts that fix them to the spindle on the mechanism. Run the wipers and stop them normally. Position the wipers in their off position and tighten the arms on the spindles.

Sep 22, 2011 | 1985 Oldsmobile Cutlass Supreme

1 Answer

Turned my wipers on in 1980 oldsmobile cutlass only one arm moved


Take your car to AutoZone and tell them. It is either the windshield wiper motor or a small plastic piece that connects the arm to the motor broke. I am leaning toward the plastic piece being broken, it is really inexpensive to fix. The people at AutoZone will be able to check it and tell you exactly hat is wrong. WARNING: watch them and what they do. some people are not as honest as others.

Mar 08, 2010 | 1983 Oldsmobile Cutlass Calais

1 Answer

How do you remove the wiper arm on a 96 olds cutlass? I removed the nut but couldn't pull the arm off.


It is just froze up, a tap with a rubber hammer should loosen it, Or try to pry it gently from side to side, Maybe some Blaster, and put the nut back on to protect the threads, and tap on the nut.

Feb 15, 2010 | 1996 Oldsmobile Cutlass Supreme Coupe

Not finding what you are looking for?
1997 Oldsmobile Cutlass Supreme Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...