Question about 2012 Toyota Sienna XLE AWD 7-Passenger V6

Open Question

2012 Toyota sienna vehicle alarm does not chirp or flash when enabled

When alarm is enabled there is no feedback to indicate that it is set. Horn doesn't sound and lights don't flash.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: toyota 1998 sienna foot break light indicator on

The brake fluid level in your master cuylinder reservoir is low.

Posted on Jan 17, 2009

  • 184 Answers

SOURCE: Indicator light for a 2003 Toyota Sienna.

Is this it? If so, it means check your tire pressure.
d0149b9.jpg

Posted on Mar 26, 2009

  • 2 Answers

SOURCE: 2007 Toyota Sienna: Dashboard warning light - What does it mean?

That light means that you are setting the tire pressure guage. there is nothing wrong with the van.

Posted on Sep 08, 2009

  • 1861 Answers

SOURCE: 1999 toyota avalon horn works intermitely

I would suggest to you to have the spiral cable (or 'clockspring') replaced. This is the electrical unit that transfers power to the air bag, the horn and the cruise control.

It is located right under the seering wheel.

Your description of the issue indicates to me that your spiral cable is loose, and making intermittant contact. If the vehicle had an air-bag deployment, this cable-device should have been changed.

Posted on Nov 11, 2009

  • 154 Answers

SOURCE: 2006 Toyota Sienna Battery Drain. Side power

the sliding door is probablly draining the battery,, have door checked.. make sure tracks are clean and hinges are not binding

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The security light on my dash keeps flashing red when I turn off my toyota sienna and lock the doors.


think its,meant too ,flash red its showing the alarms activated .if vehicle is left any length of time always disconnect the battery

Mar 12, 2015 | 2004 Toyota Sienna

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

How do I get my alarm system to chirp instead of beep when it goes off or when I lock my doors with the remote entry key fob?


Check to see if your vehicle honks when you press the "lock" button on your key fob. Press the "lock" button multiple times in a row. Many devices won't beep unless you double-tap the button after locking. If the horn doesn't honk, but the lights flash, your chirp feature is probably disabled.

Use your keyless fob and ignition key to enable the audible chirp. The process varies considerably on different makes and models. You must usually consult your owner's manual, a dealership or the alarm manufacturer for the correct process.

Jan 29, 2015 | 2006 Hyundai Tiburon

1 Answer

2004 Toyota Sienna horn blows and lights flash for no reason, then stop for a few minutes and repeat again.


If a critical supply is removed, (relay that feeds?) then the alarm will think the car has been tampered with.

Jun 14, 2017 | 2004 Toyota Sienna

1 Answer

Factory security system intermittently going off. Wondering if it is a bad sensor or switch. Does the door LED flash a code? 8 long flashes followed with normal short flashes.


CAR ALARM ISSUES


It can be any of the car doors not got properly locked or the door is locked but the switch is not sensing the door locked. Open and close each door again properly.

Or else its problem with any of switch wiring getting in contact with alarm wiring causing it to happen.

And last thing alarm connections need to be inspected. It's getting short somewhere in between.


There are few help links with solutions, to troubleshoot these types of problems. I suggest going through these links.


Click the link below: ------

Volvo car alarm keeps going off for no reason

http://technoanswers.blogspot.in/2012/07/volvo-car-alarm-keeps-going-off-for-no.html

------------------

Alarm keeps going OFF

http://technoanswers.blogspot.in/2012/07/alarm-keeps-going-off.html

--------------

2009 Toyota Camry: Hood Switch causing Alarm to go OFF?

http://whatisbyme.blogspot.in/2012/04/2009-toyota-camry-hood-switch-causing.html

----------------

Ford Pickup Alarm will not disengage?

http://technoanswers.blogspot.com/2012/01/ford-pickup-alarm-will-not-disengage.html

------------

Mitsubishi Diamante: Factory Security Alarm will not go Off

http://www.howtorepairguide.com/2012/11/mitsubishi-diamante-factory-security.html

------------

Toyota Avalon Factory Alarm will go off?

http://repairhelpcenter.blogspot.com/2012/01/toyota-avalon-factory-alarm-will-go-off.html

----------

Chevrolet Tahoe Hood open warning on dash and alarm sounds?

http://schematicsdiagram.blogspot.com/2011/12/chevrolet-tahoe-hood-open-warning-on.html

-----------

These details will help.

Thanks.

Nov 28, 2012 | 2003 Honda Pilot

2 Answers

Why my horn doesnt work 2000 toyota sienna


check fuse panel, then check wireing running from the horn. some wires corrode if not properly wrapped

May 26, 2010 | 2000 Toyota Sienna

1 Answer

Hello, i have an HID kit and i was wondering if there is a way to disable the headlight flasher that flash when i lock my doors? reason i say is because it puts wear on my HID kit...thanks


Ford F150 Manual (page 137):
Enabling/disabling the perimeter lighting feature
Your vehicle comes with the perimeter lighting feature enabled. All vehicle doors must be closed before beginning the procedure. You must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30 seconds to begin again.
1. Turn the ignition to the on position, then press the power door control three times.
2. Turn the ignition to the off position, then press the power door control three times.
3. Turn the ignition to the on position; the horn will chirp to indicate the driver configuration mode has been activated.
4. Within five seconds, press the power door control two times.

Note: One horn chirp should be heard, indicating the system has been disabled.
Conversely, a horn chirp followed by a honk will indicate the system is enabled. Pressing the power door control two times again will turn the feature on if it was previously off, or off if it was previously on.
Every two consecutive presses of the power door control after successfully entering the configuration mode will change the enable/disable condition of the feature.

5. Turn the ignition to the off position to exit programming.
Note: After exiting the driver configuration mode, the horn will chirp once to indicate a feature has been activated/deactivated.
Good luck and keep me posted if you have any more questions.

Feb 22, 2010 | Ford F-150 Cars & Trucks

3 Answers

2005 Toyota Sienna XLE - Automatic sliding door not closing.


This may or may not work depending on exactly what is wrong with the door, I cant tell what is wrong without looking at it directly however:
You can try starting with all doors closed and unlocked, keys in hand disconnecting the battery and letting the vehicle sit for 2 min or so, then reconnect the battery. Put the key into the ignition and turn it to the on position but do not start the van. Next press the button to disable the power sliding door for the drivers side, then manually open the door fully, wait 5 seconds, then close it manually fully. Press button the button again to re-enable the power sliding door, then try to use it with the automatic feature either by pulling the handle or using your remote, this may or may not work depending on if the door has somehow become de-initialized (it should work now) however if something is broken inside the door closing mechanism or door closed/open sensors, the door will continue to malfunction.

Aug 23, 2009 | 2004 Toyota Sienna

1 Answer

Gmc sierra 2008 low tire pressure problem


You can follow this to reset it.
Ignition ON, initiate the TPM Learn Mode
using one of the following procedures:

  1. On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  2. On vehicles not equipped with keyless entry, press and release the driver information center (DIC) INFO button until the TIRE LEARN message appears on the DIC display. Press and hold the SET/RESET button until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  3. Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate.
    After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
    3.1. Right front

    3.2. Right rear

    3.3. Left rear

    When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
    Ignition OFF, adjust all tires to the recommended pressures

Jan 22, 2009 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
2012 Toyota Sienna XLE AWD 7-Passenger V6 Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...