Question about 2005 Dodge Durango
How do you do it
As Mitch described, it's a piece of cake, once you know where the panel is. No need to remove tires or anything, but turning the wheels to get them out of the way helps. Thanks, Mitch!
Posted on Feb 12, 2009
SOURCE: head light 2005 altima
you have to remove the bulbs from inside of the hood in the engine compartment. in some cars you have to remove some "pins' and remove the entire headlight assembly.. You then remove the holder where the lightbulb is located and replace the bulb.
Posted on Nov 18, 2008
There are 3 machine bolts that hold the big white part of the head light to the truck. These bolts are black and I think 7/16 but not completely sure, maybe 12mm or so. You'll need sockets, ratchet and a really long extension. Two regular extensions won't reach the bottom one. You get to all three of them from the front of the truck straight in. Once those are out, the head light assembly pulls forward and can dangle from about 10-12 inches of extra wire. This is attached to the bulb harness. 1/3 of a turn and the wire and bulb come out of the head light. Pop the new bulb back in WITH GLOVES, do not touch those halogens. And put it back together. You can use peanut butter in a deep well or regular socket to hold the screws in to get them started, or the rag thing.
It took me 14,607 hours to find these bolts and about 10 minutes to do the job! Hope it helps out!
Posted on Feb 25, 2009
Thank you for sharing the information on the light bulb. You just saved me money from having to take my 2003 Trailblazer in to have the low beam bulb replaced. I did exactly what you said.
1 Open hood and lock.
2. Take filter cover off (4 screws and they stay with the filter).
3. 3 inch cover pulls off.
4. Twist light bulb 1/8 turn.
5. Unclip the wiring harness to light bulb assembly.
6. Test by turning light switch on.
7. Align assembly with light housing and turn 1/8 until it snaps in.
8. Put 3 inch cover back on.
9. Place filter cover back on and hand tight the 4 screws.
10. Close hood.
Posted on Aug 25, 2009
The adjustment screws/nuts should be located either on the top of the headlamp assembly,
behind the headlamp assembly, or near the frame rail by the radiator
You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well
Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. Also mark where the center of the bulbs would be (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)
For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall. For horizontal, aim the hot spot directly at the line you marked for the center of your bulbs
For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
Posted on Nov 04, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Oct 11, 2015 | Honda Cars & Trucks
Mar 19, 2013 | 2001 Dodge Durango
Mar 17, 2013 | 2005 Dodge Durango
Dec 14, 2009 | 2001 Dodge Durango
Aug 29, 2009 | 2001 Dodge Durango
Jun 08, 2009 | 2005 Ford Escape
Mar 01, 2009 | 2001 Dodge Durango
Dec 19, 2008 | 1999 Dodge Durango
Nov 12, 2015 | 2005 Dodge Durango
904 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: