Question about Peugeot 406

Open Question

Peugeot 406 break rear seat belt in the midle are stuck. How can I repair or replace mechanism?

Year 2003. product, 2,0 HDI

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: cigarette lighter fuse peugeot 406

fuse box under the steering wheel .. check fuse F23!

Posted on Feb 23, 2009

Ad
  • 6 Answers

SOURCE: Peugeot 406 HDi jumps out of 5th gear

sometimes a nut comes loose behind the end cover on ml5 box.

Posted on May 04, 2009

pippall
  • 1486 Answers

SOURCE: 406 hdi pass door lock wont lock so car wont lock

Remove the door pannel and spray releasing oil over the central locking solinoid.That should sort it for you good luck.

Posted on Sep 02, 2009

  • 205 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: peugeot 406 hdi wipers problem

i have the same problem.Have u had any luck with urs yet???

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the engine number not code on a peugeot 406 2.0 hdi 2003


it will be stamped on a flat surface of the engine , different makers use different positions, it will be below the head as its the engine block that is numbered just have to clean it off and have a good look around , usually on one of the sides , good searching, or contact Peugeot with the rest of the vehicle details

Oct 07, 2014 | 2005 Peugeot 406

1 Answer

Peugeot 406 hdi faults


Cam belts are due every 120,000km on peugeots. You should be fine for quite a while.

Sep 07, 2014 | Peugeot 406 Cars & Trucks

1 Answer

Peugeot 406 hdi 90 2003 problem bsi


have heating in my peugeot 406 hdi when car is ticking over but when i drive for few mins the heater goes cold

May 03, 2012 | 2005 Peugeot 405

2 Answers

Peugeot 406 estate 2l hdi, anti polution light on


it would never be 1000 euros!!!!!!!!!!!! it will be part of the exhaust system it cuts out because its causing pollution

Sep 15, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 406 2.0 HDI 99th,if i breake wit engine its go of


does it return to idle when at 900, this is programmed to shut off fuel injectors when car is pushing engine to save you fuel for when going down a hill, u push clutch and a signal tells it u have which returns back to idle.

Jul 04, 2009 | 1989 Peugeot 405

1 Answer

Air bag light flashing on dash


yes you got it, i always repair these, i cut out the connections and replace, it lasts about a year then they have the same again, rarely i do the passenger side, start with driver then passenger.

Mar 12, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 406 hdi 2000 [Wreg] front @rear fog


Send me your car chaisses number to get the wiring diagrem for helping

Mar 02, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 406 HDi jumps out of 5th gear


sometimes a nut comes loose behind the end cover on ml5 box.

Feb 21, 2009 | 2005 Peugeot 405

2 Answers

Peugeot 206shredding fan belt. alignment ok pulleys ok


You've covered all the reasons why fan belts shred. I would suggest looking closer, and making sure the bearings are good in all belt driven devices.

Reply back if you have any further questions.

Feb 02, 2009 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...