Question about 1987 Ford Bronco

1 Answer

Bronco 2 i have a 1988 ford bronco 2, it died and wont start, it just makes a clunk,clunk noise when trying, any ideas to try, I would appreciate any help, thanks.  we put a new starter in it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Clunk-clunk? Sounds like the flywheel broke. Maybe (if it's an automatic) the torque convertor came unbolted from the flywheel. I hope that I could help you. Best wishes.

Posted on Jan 25, 2009

  • Bryon Agin Jan 29, 2009

    How is your Bronco doing? Just wondering.

    Bryon

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

Bronco wont start makes clicking when truned over


try jumping your battery and see if it starts

Feb 21, 2013 | 1989 Ford Bronco

2 Answers

1987 ford bronco engine wont start


there is a two piece control module and pick up in distributor you could replace these or try a used distributor

Jul 23, 2009 | 1987 Ford Bronco

1 Answer

1989 Bronco starts but dies after a couple of seconds


try checking the thermostat control senser. it caused my bronco to start for a second and then die. after a while it would finally start and run for a while then die driving down the road. i changed the thermostat control senser and it fixed all problems of dieing

Apr 27, 2009 | 1989 Ford Bronco II

1 Answer

Bronco try's to die when i turn on the lights


have your altinator check at your local parts store. if that doesnt work chek the grounds to make sure they are good and tight. but it does sound like your alt is going bad

Mar 14, 2009 | 1995 Ford Bronco

1 Answer

1995 ford bronco eddie bauer 5.0


sounds like your rear differential is about to go out you should take it in to a shop right away before you get stuck somewhere. they will have to rebuild it.

hope this helped.
please rate well

Mar 03, 2009 | 1995 Ford Bronco

1 Answer

I have a 1990 ford bronco and it has began to make a noise when i change geqars i was thinking maybe u-joints?


if it makes a clunk sound when u put it in a gear then yes u joints are needed and soon as they will break and cause the driveshaft to break loose and serious accendent could occur

Jan 19, 2009 | 1990 Ford Bronco

2 Answers

Died and now wont start


CHECK IGNITION MODULE ON DIST. THATS THE MOST COMMON PROBLEM WITH THIS MODEL

Jan 15, 2009 | 1989 Ford Bronco

2 Answers

Bronco Wont Start (help please)


Check for timing gear problems. They have plastic teeth on the cam shaft gear which will shatter causing it to jump time.

Aug 03, 2008 | 1981 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...