Question about Toyota Cars & Trucks

Open Question

Vacuum hose connection

1983 toyota hi ace 2yc engine problem finding where it goes one hose only

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: dpfe sensor broke in the REF tube

One hose is reference the other is pressure, the hoses are different sizes, do you have the factory high-temp silicone hoses required? they are different sizes so you can't mix them up, vacuum hose will burn up in short order, the failure of this sensor is almost always caused by excessive exhaust back pressure, you may have a cat converter starting to plug up.

Posted on Oct 13, 2008

Ad
  • 193 Answers

SOURCE: 1989 jeep 4.2 engine vacuum hoses

I can't tell you were to get one, except at a dealer, but what you need is a vacumn diagram. They are similar to an wiring diagram.
Bill

Posted on Nov 26, 2008

  • 1596 Answers

SOURCE: I need the vacuum diagrams for a 1984 Toyota 4x4 22r engine

try to send did you get em ?

Posted on Jan 13, 2009

dmsr63
  • 2050 Answers

SOURCE: I require a vacuum hose diagram for Toyota 22R AUS

I have a 1989 toyota truck, and it's located under the hood. It's an emmisions sticker with the vacuum routing on it.

Posted on Nov 24, 2009

BCAS1298
  • 3092 Answers

SOURCE: Vacuum hose missing

Your PCV valve has two port's, it also should have came with a plug ( Plastic ) That you break off of the PCV and plug the small one.Canada Emissions is the only one that uses both port's.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota engine 1rz


rough idle can be caused by vacuum leak, test the lines into the intake, if the dont hold vacuum, follow the line to detect the cause. Also the PCV could be broken and lead to a wrong air mixture. If check engine light is on I would expect lean bank codes...

Apr 19, 2014 | 1995 Toyota Hi-Ace

1 Answer

Vacuum hose


I never heard of a vacuum line going from the throttle body/intake manifold before but I have never worked on a Kia. Disconnect the hose at both ends have some one take you to ace hardware they have automotive vacuum hose by the foot bring your old hose with you so they can cut the proper length and girth of your original hose and pop the new one back on. It might be hard to fit the new hose back onto their fittings i usually lightly oil the surface that the hose goes over with engine oil so it goes on pain free remember lightly oil. good luck.

Mar 27, 2014 | 2001 Kia Sportage

1 Answer

Need a carburetor vacuum hose diagram 1983 dodge rampage


Vacuum diagram? - Turbo Dodge

www.turbododge.com > ... > Carburetted and TBI Injected . you should be able to find every thing you want to know here

Feb 04, 2012 | 1983 Dodge Pickup

1 Answer

I have a 1982 landcruiser - ran fine - then changed the air pump - and now won't start unless full choked and won't idle at all - did i misplace a vacuum hose ? I can't find a vacuum hose diagram anywhere....


Do you mean vacuum pump? If so you probably need to change ALL vacuum hoses. With the new pump comes new vacuum pressures, old hoses will probably be sucked off their pipe nipples or small cracks turn into large ones, one or both of the above will cause severe rough idle and running along with much power loss and fuel mileage will ****. If you have the original service manual on the truck and engine (I am assuming you have the 4.2L straight 6- 2F) it has a vacuum hose routing view in it. good luck
Rickster

Aug 09, 2010 | 1983 Toyota Land Cruiser

2 Answers

1983 Buick LeSabre Wagon, cuts out driving down the road


Find the EGR valve on the intake and locate the vacuum hose that is connected to it. Start the engine cold and as it warms up, pull the hose off and if it idles and drives fine, the EGR valve is bad and needs to be replaced. Please rate me on this answer.

Jun 29, 2010 | 1983 Buick LeSabre

1 Answer

Engine trouble with my 1983 toyota pickup


Toyota engines have a built in TSTV- thermo controlled vacuum system where vacuum is applied to the choke system in various levels as according to the temp. of the engine. If the TSTV is faulty or if the vacuum pipes are incorrectly placed then you have a choke which is not opening up properly. Fuel is thus not burnt completely and due to the incomplete combustion there is a formation of soot on your exhaust. Try to get the choke to open up in relation to the temp of the engine. The fuel/air ratio alse needs to be checked ( idle mixture control) once you have the vacuum system working properly.

Nov 19, 2009 | 1983 Toyota Pickup

1 Answer

We need a picture of how to replace carburator and hoses


any chilstons or haynes manual will have a diagram

Aug 23, 2009 | 1983 Toyota Pickup

2 Answers

Need diagram for 1983 camaro vacuum hoses with the emissions stuff taken off has a 305 4bbl


Injected or carb? If all emissions stuff is removed are you replacing it or just making stuff work? If usst making everything work, you need a hose from carb to vacuum advance on dist (if you have one) You can try putting the line above the throttle plate or below it and see which best suits your needs.. There is a large hose that goes to the brake power booster from the back of the carb (if power brakes, Another line goes to the vacuum system under the dash (makes heater controls operate) That line can go to a fitting on the manifold or any other full time vacuum connection on the carb base. All other connections can be blocked off.

Jun 16, 2009 | Chevrolet Camaro Cars & Trucks

2 Answers

Vacuum line schematic 1987 toyota corolla le front wheel drive


It is similar to my rear wheel drive two door.

The main vacuum line from a vacuum source on the intake goes to the multi-hose valve on the top and the distributor vacuum advance.This multi-valve switching valve is the main connection to the other vacuum hoses on mine. Two lines come in from a vacuum source and thre go out to three components according to tempature. On mine the middle one off to side 1)goes to choke opener and switching vacumm valves mounted on the fenders the other middle one 2)second from top goes to another choke opener and EGR Valve and EGRModulator. The bottom hose connection is on when cold 3)and goes to a part on the carburator to help it run better when warming up a AAP valve.

There is a check valve diaprham thing inline to the EGR vlave on the second line from top.

I have another vacuum line on the drivers side of the carburator that has a check vlave inline but larger it goes to the throttle linkage to help slow the closing of the trottle on rapid deceleration.126c338.jpg14b3a33.jpgf95de67.jpg9f023f4.jpga890bd7.jpg5531e92.jpg

Mar 15, 2009 | 1987 Toyota Corolla 2 Door

1 Answer

1998 gmc jimmy has no 4x4 anymore


Hi there. under your battery is the 4x4 actuator. there should be a vacuum hose that is connected to it. this actuator is the one that will lock your front diff in 4x4. this hose could fall off and you will not have 4 wheel drive without it connected.If that hose is connected, there is another hose which comes from the vacuum switch up the back of the engine and over toward the driver side of the engine compartment. it tees off and one end goes to a little resevoir on the engine hood. with the engine running, check to see if you have vacuum to this hose. also with thye engine running press the 4x4 switch and make sure that the actuator os working. the vacuum should **** the diaphram in and hold it in. If there is vacuum to the diaphram when 4x4 is engaged but the diaphram doesn't hold, you will need a new actuator. Hope this helps you.

Dec 29, 2008 | 1998 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...