Question about 2002 Mazda Protege

1 Answer

Key fob slow to respond

The key fob has worked fine for 6 years but now I have to press the button several times to lock or unlock. Any ideas?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Yes its a battery insde them just replace it

Posted on Jan 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Hyundai Tiburon GT, the key fob doesn't work. I got battery checked, they're fine. Any ideas how to make the key fob work? It has an unlock and a lock button.


Place key in ignition, turn but do not crank up the motor and press the lock/unlock buttons to program it for your vehicle. You should see the lights flash on/off confirming a successful link.

Feb 14, 2011 | 2003 Hyundai Tiburon

6 Answers

Remote entry keyfob control doesn't work. Batteries are good.


Unfortunately theres not a lot you can do with them. If you are sure the battery is OK and the contacts are clean and it still doesn't work then a trip to the dealers to get it reprogrammed or replaced is in order.
Can you see any moisture inside? any chance you dropped it in the rain by accident?
If by any chance it has come into contact with moisture try drying it out somewhere warm but not hot as that may cause more damage.

Aug 08, 2008 | Jaguar XJ8 Cars & Trucks

1 Answer

Bmw 325 on a y reg will turn over but will not fire fault code pointing immobilizer fault anti tamper fault any ideas easy cheap fix thanks


Hi Mark you could try to see if re-programming the key might do it, you could also disconnect the battery for 10 minutes and see if it resets that way...to re-program the key this is what you do, please follow by the book or it wont work, this however is just a trial to see if it will do the job, if reprogramming the key does not do it, then disconnect the battery for ten minutes and then try re-programming of the key...
1, unlock the car with the key ( not fob) get in and shut the door 2, switch ignition on and then off ( do not try to run it just on then off) 3, remove ignition key 4, press and hold unlock button 5, press lock button 3 times quickly all within ten seconds keeping the unlock button pressed 6, release unlock button 7 ( if you have this type of key fob) the led will flash slowly for 10 seconds 8,( if you have this type of key fob) the central locking system will lock and unlock rapidly to indicate correct programming 9 ( if you have this type of key fob) repeat procedure if the led flashes constantly, or the locking system does not unlock and lock rapidly please follow as directed..if you have any problems understanding what to do, please contact me on email address s.e.morris@live.co.uk hope this helps

Jan 13, 2011 | 2001 BMW 325

1 Answer

I have a 2004 Honda Accord EX. Key Fob works trunk but not doors


Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. A maximum of 3 keys can be programmed. Close all doors and boot/tailgate. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press key lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press key lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press key lock or unlock button. Within 10 seconds: Press lock or unlock button of first key. System should now lock or unlock vehicle. Press lock or unlock button of second key. System should now lock or unlock vehicle. Press lock or unlock button of third key. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed keys.
NOTE: If less than 3 keys are to be programmed, remove ignition key after programming last key.

Jan 25, 2010 | 2004 Honda Accord

3 Answers

TWO KEY FOB IS NOT WORKING ONLY ONE


Have all keys with you inside the car and repeat again with the second key within 30 seconds...... "Press and hold the 'unlock' button while at the same time pressing the center 'lock' button three times. On the third time, release the 'lock' button at the same time you release the 'unlock' button." If you have a key with three buttons, ensure doors are unlocked. Put key in ignition and turn key over to 2d position where dash lights, etc come on. Pull key out. Press and hold the "unlock" button while at the same time pressing the center "lock" button three times. On the third time, release the "lock" button at the same time you release the "unlock" button

May 20, 2009 | 2003 Mini Cooper

2 Answers

Key fob will not undo cetral locking or disable car alarm changed battery in key fob still having no luck any idea who can re code key fob to central locking and alarm?


If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.

Oct 16, 2008 | 2001 Chrysler PT Cruiser

3 Answers

Door locks dont operate with remote key fob


Touch Key metal to lock cylinder metal then unlock

Jul 29, 2008 | 2001 BMW 325

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

2 Answers

Keyless entry remote


Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...