Question about Chevrolet Silverado 1500

Open Question

Where is the oil pressure sensor on a 2006 Chevrolet Silverado

Oil pressure sensor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rick_amick
  • 69 Answers

SOURCE: 2005 Chevrolet Silverado 2500HD 4x4 Oil Change Reset

Not positive 05 is the same but on my 02 you turn the key to the on position and pump the gas pedal 4 times.

Posted on Mar 30, 2009

Ad
  • 7353 Answers

SOURCE: Replacing Oil Pressure Sensor.

Usually near the filter.

Posted on Dec 16, 2009

  • 258 Answers

SOURCE: WHERE IS THE OIL SENSOR LOCATED ON A 5.3 CHEVROLET

these chevs are known for oil pressure switch going bad its located on theback right side of the engine it is replace able without having to remove anything u will need a mechanics mirror to see it

Posted on Jan 23, 2010

  • 335 Answers

SOURCE: when to do a tune up on a 2006 chevrolet silverado...

Hello, the spark plugs are good for 100,000 miles on this vehicle. when you get close to 100,000 miles is when you should tune it up

Posted on Jun 19, 2010

thark01
  • 114 Answers

SOURCE: where is the oil pressure sending unit located on

Its in the rear/ top /center. Hidden alittle, you can get it out with a special socket and it's not hard to access.

Posted on Jan 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I check and replace engine oil sensor.


Knowing how these gauges work , I'd say you have an instrument cluster problem not oil sender unit. 2003 - 2006 GM had bad stepper motors in the instrument cluster . If there was a problem with the oil sender the gauge would default to zero .
Engine Oil Pressure Gage
The instrument panel cluster (IPC) displays the engine oil pressure as determined by the powertrain control module (PCM). The IPC receives a class 2 message from the PCM indicating the engine oil pressure. The engine oil pressure gage defaults to 0 kPa (0 psi) or below if:
?€¢
The PCM detects a malfunction in the engine oil pressure sensor circuit.

?€¢
The IPC detects a loss of class 2 communications with the PCM.

If you don't know what class 2 serial data communications are ,google it. How to repair GM Instrument Cluster Speedometer Gauge Stepper

Dec 23, 2015 | 2003 Chevrolet Silverado 1500

2 Answers

I have a 2006 chevy silverado 5.3L..When in idle oil pressure gauge goes to 80 and when i accelerate ail pressure goes to zero ...is it the oil sending unit?


It could be the sending unit. If the truck is low on oil it will cause something similar. Be sure the oil level is topped up. The only way to be sure it so measure the actual oil pressure at the engine with a proper gauge..

May 07, 2011 | 2006 Chevrolet Silverado 1500 2WD

2 Answers

WHERE IS THE OIL SENSOR LOCATED ON A 5.3 CHEVROLET SILVERADO LS 1500. MY OIL GAUGE WENT TO 80 PSI WHEN I STARTED IT UP. WOULD THERE BE SOMETHING ELSE WRONG OTHER THAN THE SENSOR.


these chevs are known for oil pressure switch going bad its located on theback right side of the engine it is replace able without having to remove anything u will need a mechanics mirror to see it

Jan 23, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

The oil sensor needs to be replaced where is it


  1. Remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    0996b43f802053c4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor-8.1L engines

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the sensor to 22 ft. lbs. (30 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.

Nov 15, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Can't find the oil sensor on my 03 Silverado.


If you're refering to the oil PRESSURE sensor for your guage, check in the area near your oil filter. They are typically close to that location.

Jun 25, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

2005 chevy silverado with low oil pressure


You should replace your oil pressure sensor its cheap and easy to do...

Steve

May 16, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2006 chevrolet silverado oil presure guage goes directly to 80 when switch is turn on and motor is running.


The oil pressure switch is grounded. You will need to replace the oil pressure switch.

Mar 11, 2009 | 2006 Chevrolet Silverado 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...