Question about 1998 Toyota Camry

1 Answer

How to remove the counter balance gear on the crankshaft

I bought a crankshaft with oversize inserts but the counter balance gear on the crankshaft is not on it so I have to take the gear off the old crankshaft. I have no idea how to do this. Can I remove it by hitting it or does it need to be pressed off and back on the new crankshaft?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

The best advice is to have it pressed off and then pressed on to the other shaft. Hitting it WILL damage the gear.

The graciousness of a FixYa rating for my assistance would be greatly appreciated; Thanks in advance.

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 f-250 7.5l harmonic balancer removal how do you remove it


no set bolt you will need a harmonic balancer puller some truck take a special puller

Jan 05, 2016 | Cars & Trucks

1 Answer

How to locate timing on the counter weigth balancer


check for all marks or make your own. to replace

Jan 22, 2013 | 2006 Toyota Camry

1 Answer

Need to know timing marks have a S70 and I am doing a timing belt and would like a diagrams on the marks for this belt


  • Align the marks on the timing gears before removing the belt
ironfist109_374.jpg

  • Line up the balance shafts before installing the belt
ironfist109_376.jpg

  • Check the alignment of the balance shafts and crankshaft before tightening the tensioner.
ironfist109_377.jpg

  • Use an Allen wrench as a counter-hold when tightening the tensioner pulley.
ironfist109_378.jpg

  • Pulley alignment marks for timing belt replacement.
ironfist109_379.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony


Oct 12, 2011 | 1998 Volvo V70

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

1 Answer

The serpentine belt pulley on the crankshaft dampener has separated from the dampener and is moving forward, throwing the belt off. It is about 1/2 inch forward, and a black rubberish gasket is working...


yes, you need a new dampener. You will need special tool--a puller. the procedure from autozone.com is as follows:
  1. Remove the drive belt.
  2. Raise and safely support the vehicle.
  3. Remove the right front tire assembly.
  4. Locate and remove the right splash shield.
  5. Remove the crankshaft balancer bolt and washer. (my note: you may need to remove the starter and lock the flexplate starter gear with a screwdriver to hold the engine while loosening the damper bolt)
  6. Remove the crankshaft balancer using a three-leg puller such as J 24420-B, or equivalent.


2507b44.gif


Fig. Crankshaft balancer removal-3.1L engine


To install:

  1. Clean all parts well. Apply a thin coat of sealer GM #12345739, or equivalent, to the keyway of the balancer. This is to help prevent oil from wicking along the keyway and causing a leak.
  2. Install the crankshaft balancer using tool J 29113 Crankshaft Balancer Installer or equivalent, to draw the balancer onto the crankshaft. Do not hammer on the balancer. (my note: I have never needed this tool. I slip the balancer on and draw it in with the bolt)
  3. Install the crankshaft bolt and washer and torque to 76-80 ft. lbs. (103-108 Nm).
  4. Install the remainder of the components in the reverse order of removal.

Oct 24, 2010 | 1999 Buick Century

1 Answer

My balance shaft belt broke while I was driving. It stripped some of the teeth off the timing belt and Im pretty sure it jumped time. I need a diagram to show the timing marks and how to get it back in...


see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Sep 20, 2010 | Honda Odyssey Cars & Trucks

            1 Answer

            Wiich is the torque specifications for crankshaft


            Crankshaft endplay is controlled by the thrust bearing. Endplay tolerance is usually from 0.004"-0.006" for a crankshaft with a 2" to 2 3/4" main bearing diameter. If crankshaft endplay is too great, oversized thrust bearings or inserts may be available.

            Jul 23, 2010 | 1999 Dodge Intrepid

            1 Answer

            How i fix timing of lantra 1600 cc 95


            Disconnect battery earth lead. Do not turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of ratation unless otherwise stated, Support engine. Remove, engine mounting, auxilliaty drive belts. Water pump pulley 1. Crankshaft pulley bolts 21. crankshaft pully 2. timing belt covers 3. Turn crankshaft to TDC on No 1 cyclinder. Ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket and balancer shaft sprocket timing marks aligned. Timing marks on camshaft sprockets should align with cylinder head upper face. Dowel pins on camshaft sprockets should face upwards. Slacken tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove, automatic tensioner unit bolts. Automatic tensioner unit. Timing belt, crankshaft centre bolt, crankshaft sprocket. Crankshaft sprocket guide washer. Slacken blancer shaft belt tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove balancer shaft belt.

            Installation
            Ensuring timing marks arligned. Note timing marks on camshaft sprockets should align with cylinder head upper face. Exhaust sprocket mark is on recess, but inlet sprocket mark is on tooth. Note: to check oil pump sprocket positioned correctly, removing blanking plug from cylinder block. Insert 8mm diameter Phillips srcrewdriver in hole. Ensure screwdriver is inserted 60mm from face of cylinder block. if screwdriver can only be inserted 20mm: turn oil pump sprocket 360°. Insert screwdriver again. Fit balancer shaft belt in anti-clockwise direction, starting at crankshaft sprocket. Slacken balancer shaft belt tensioner bolt. Turn tensioner clockwise to tension belt. Tighten bolt to 15-22Nm. Apply thumb pressure to belt. Belt should deflect 5-7 mm. If not repeat tensioning procedure. Install crankshaft sprocket guide washer, crnakshaft sprocket. Tighten crankshaft cente bolt. Tighten torque:110-130 Nm. Note ensure crankshaft sprocket guide washer is fitted correclty. Oil treads and contact face of crankshaft body before fitting. Check tensioner body for leakage or damage replace if necessary. Check pushrod protrusion is 12mm. If not replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Resistance should be felt. Place flat washer under tnesioner body to avoid damage to body end plugs. Retain pushrod with suitable pin through hole in tensioner body. install automatic tensioner unit to cylinder block. Tighten bolts to 22-27Nm. Fit timing belt in anti-clockwise direction, starting at the tensioner pulley. Slacken tensioner pulley bolt. Turn tensioner pully clockwise to temporarily tension belt. Tighten bolts to 43-45Nm. Turn crankshaft slowly 1/4 turn anti-cockwise. Turn crankshaft clockwise until timing marks alligned. Slacken tensioner pully bolt. Fit tool to tensioner pulley. Tool No 09244 28100. Apply clockwise torque of 2,6-2,8 Nm to tensioner pulley. Tighten bolt to 43-45Nm. Insert special tool in timing belt rear casing. Tool no 09244-28000. Screw in tool until pin can be removed from automatic tensioner unit. Remove special tool. Tool nr 09244-28000. turn crankshaft two turns clockwise. Wait 15 minutes. Ensure timing marks aligned. Check extended length of pushrod is 3,8-4,5mm. Install components in reverse order of removal. Tighten crankshaft pulley bolts, Tighten torque 20-30Nm

            Nov 01, 2009 | 1995 Hyundai Elantra

            1 Answer

            I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


            Dear Friend
            Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
            Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

            Installation:
            ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
            Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
            Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

            Sep 21, 2009 | Hyundai Elantra Cars & Trucks

            2 Answers

            How to find timing belts marks toyota rav4 2l


            there is a hole in the cam gear that if you look through it with a mirror and light you should see a small notch in the cam cap. on the crank gear there is a small divot between the teeth just to the left of the keyway notch that should align with a small dimple on the oil pump cover

            Oct 14, 2008 | 2000 Toyota RAV4

            Not finding what you are looking for?
            1998 Toyota Camry Logo

            Related Topics:

            225 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Toyota Experts

            yadayada
            yadayada

            Level 3 Expert

            60667 Answers

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            21936 Answers

            Jeff Turcotte
            Jeff Turcotte

            Level 3 Expert

            6811 Answers

            Are you a Toyota Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...