Question about Subaru Forester

Open Question

Remove the drivers side inner door panel on a subaru forester

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Ajkill
  • 2035 Answers

SOURCE: My 2003 Forester driver side window wont work.

You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Posted on Oct 21, 2008

Ad
Molson02536
  • 3854 Answers

SOURCE: How do I remove the drivers side inner door panel.

Best thing to do is go to Auto Zone and buy some extra door panel clips, the old ones will most likely break and when you try to place the door panel back on you can't. The clips are not that expensive and Auto Zone can give you the step by step instructions and tell you what tools your going to need to remove the old clips with out damaging the door panel. If you don't want to buy the door panel tool, Auto Zone also has a tool loner program. 
Good luck and hope this helps. If you need instructions, keep me posted and be glad to help.

Posted on Jun 07, 2009

  • 1986 Answers

SOURCE: Installing replacement side mirror on 2007 Subaru Forester

yes... you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can access the bolts holding the mirror on and disconnect the wiring harness as well..

Posted on Aug 20, 2009

rteemon
  • 578 Answers

SOURCE: 2000 Subaru Forester drivers side outside door handle has jammed

take off inside door panel and check the linkage on the lock may be broken

Posted on Sep 16, 2009

Testimonial: "Thanks for that ... I'll give it a go. Cheers."

damo555
  • 231 Answers

SOURCE: how to remove the lock cylinder from the driver's

Hi by removing the door card and removing a retaining surclip that holds it onto the door handle from the inside it should then just slide out

Posted on Apr 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Subaru forester wiring


Remove the window switch & test it

If it is good--- remove the door panel

Then your going after the window regulator or motor

Apr 04, 2014 | 2005 Subaru Forester

1 Answer

How to remove the lock cylinder from the driver's side door on my 98 Subaru Forester?


Hi by removing the door card and removing a retaining surclip that holds it onto the door handle from the inside it should then just slide out

Mar 31, 2011 | 1998 Subaru Forester

1 Answer

Where is main computer in 1998 Subaru forester located


The main ecu or engine computer is located under the passenger side floor mat. You will have to remove or peel back the carpet to access it. if you remove the kick panel near the door first it will be easier.

Feb 18, 2011 | 1998 Subaru Forester

1 Answer

How do you remove the door panel drivers side for a subaru forester 2001, I have most of the screws out but the top of the panel will not come lose for some reason,


Once all screws and connections (plastic pops at the bottom of frame and window control module) are disconnected slide plastic frame away from the dash. Should slide out with a little force, also, make sure to remove the screw in the tweeter speaker compartment, often forgotten. Hope this helps.

Dec 31, 2010 | 2000 Subaru Forester

1 Answer

2000 Subaru Forester drivers side outside door handle has jammed


take off inside door panel and check the linkage on the lock may be broken

Sep 15, 2009 | 2000 Subaru Forester

1 Answer

Driver door on a subaru forester 2003. window will not go up or down. window is still in the track and the motor is still working


Could be a bad regulator or a bad guide rail pinning the window

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you should be able to see what's restricting the window from moving

Sep 15, 2009 | 2003 Subaru Forester

1 Answer

Installing replacement side mirror on 2007 Subaru Forester


yes... you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can access the bolts holding the mirror on and disconnect the wiring harness as well..

Aug 20, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

Window stuck - 1998 Forester Limited


I installed speakers in my door panels.
Pop up the window controlls unplug switches,
remove plastic screw hiders to expose phillips screws
remove screw from door latch lever
pull out on door panel, then lift up
its not too hard good luck
lowrob77@yahoo.com

Jan 10, 2009 | 1998 Subaru Forester

1 Answer

My 2003 Forester driver side window wont work.


You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Oct 21, 2008 | 2001 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...