Question about 2003 Chrysler Town & Country

Open Question

Rear window wiper doesn't work

Fluid comes down, but wiper fails to touch

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: rear wiper does not touch window

I have this same problem and I was told once it is above freezing here to wash it and lubricate the hinge and spring. They said those get gunked up and won't move with the window correctly which causes this problem. This week I hope to try it since it will finally be warm enough!

Posted on Jan 14, 2010

  • 880 Answers

SOURCE: I have a 2007 Town

If it is not touching the glass the arm is bent. Raise the arm away from the glass. Grasp the arm near where it is mounted to the body and near the wiper blade with the other hand. Slightly bend the arm toward the glass. Only bend the arm a very slight amount and check to see if there is enough pressure for the wiper blade to work correctly. Repeat this until the wiper blade cleans the glass properly. DO NOT over bend the wiper arm as too much pressure will cause the blade to wear out very quickly.

Posted on Dec 22, 2010

SOURCE: I have a 2006 Chrysler

Remove the washer tank & test the pump

Probably quit

Posted on Jun 26, 2011

  • 444 Answers

SOURCE: headlights won't come on

Multi function control switch has to be replaced.

Posted on Nov 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield wipers working intermittently. Sometimes takes 5 minutes before they begin to work. Other times stop in mid wipe.


This is the wiper motor failing...But to be safe unplug wiper motor,turn on wiper switch,connect test light to negative side of battery or good solid metal ground and stick probe in connector.if it is not working and the test light is not on then the wiper switch has failed.....and if the test light comes on at connector the wiper motor has failed..Since it works intermittently have an assistant to work the wiper switch and test a number of times to be sure.You can buy a cheap test light that will be good enough to check this at any auto parts store...BEFORE YOU BEGIN YOUR TEST MAKE SURE TEST LIGHT
HAS GOOD GROUND BY CLAMPING TO NEGATIVE SIDE OF BATTERY AND TOUCH PROBE TO POSITIVE SIDE OF BATTERY TO ENSURE GOOD CONNECTION...LIGHT WILL COME ON.

Feb 28, 2011 | 2005 Volvo XC90

2 Answers

Windshield wipers work sporaticly, washer motor doesn't pump out the washer fluid???


wiper motor bad washer pump is part of wiper motor you pick a good one up at a junk yard for around $35.00

Jan 04, 2011 | 1998 Chevrolet S-10 Pickup

2 Answers

Windshield wiper fluid not coming out


remove the hose from the wiper arm and see if when you push the washer button that the fluid comes out the hose,if it does the sprayer nozzel is plugged if not replace the pupm

Dec 02, 2009 | 2001 Oldsmobile Alero

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

Windshield wiper water


The washe pump is a known item that will fail, especially if the washer fluid froze one time. If the hoses are all clear, replace the washer pump motor.

Apr 05, 2009 | 1998 Toyota Corolla

1 Answer

REAR WIPER.....


check the outside first pull the fluid line where the fluid should be coming out have someone stand there if it comes out there the nozzle is plugged work a pin or needle inside of it to loosen it up if thats the case

Jan 25, 2009 | 2000 Jeep Grand Cherokee

3 Answers

I have a 2003 Chevy Trailblazer Windshield Wiper problem.


As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Nov 25, 2008 | 2003 Chevrolet TrailBlazer

1 Answer

2003 Oldsmobile Silhouette - Rear Wiper not working


This sounds like the wiper motor has failed. It is a common problem that usually starts with the wipers moving slower than normal, then eventually quits all together.

Nov 19, 2008 | 1997 Chevrolet Venture

3 Answers

WINDSHIELD WIPER FLUID WILL NOT COME OUT BUT WIPERS DO MOVE


the pump working? hoses cut or disconnected?

Oct 25, 2008 | 2003 BMW 5 Series

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...