Question about 1995 Ford Thunderbird

1 Answer

My door is stuck shut.handels not working inside or out.i have pulled the door panel out a little.but im not sure what to look for inside to make it open. can you help?

The window was off track. it was falling down,so i put a wedge in the outside of the window to keep it up. maybe i knocked something off?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 165 Answers

Follow the wire that goes up to the door latch and pull up and down it should open

Posted on Jan 17, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sicaudio
  • 96 Answers

SOURCE: Driver's side door power locks are stuck; door stuck shut.

sounds like the rods are disconnected the clips hold the rods in place the latching mechanism holds the handle in place as well did you replace the speakers or did a shop? if a shop did then they caused this if you did then you may have caused this either way untill you reattach the rods none of it will work. you will have to manually open the door at the latch from inside teh door behind the panel.

Posted on Jul 19, 2008

  • 173 Answers

SOURCE: Door latch frozen open

saturate latch(best you can) with wd40 after cleaning.Clean with starting fluid then lube with wd 40

Posted on Dec 09, 2008

  • 1 Answer

SOURCE: Door won't unlatch or come open

Ford had a problem with the door handles not working properly. They are cheap plastic. If the exterior door handle is broken, you will need to drill out the rivets that hold it in, and then get the door open and the panel off. You have to disconnect the rod going to it. Then, remove the handle. If you don't want to drill again, I suggest replacing the rivets with a bolt and nut easily obtainable at your hardware store. I've found that a M7 bolt works very well. If you are having a problem with the interior door handle, it's the same problem. Remember to check your door latch because if your exterior handle is broken, then your latch isn't working properly. I got one at Ford for about 40 bucks.

Posted on Mar 07, 2009

  • 58 Answers

SOURCE: Drivers electric window stuck in down position

actually you have thought of all but the prob. The track has jumped, making the motor not move the window. Sometimes you can gently slide the window up by hand and then the motor will catch the track and finish rolling the window up

Posted on Jul 05, 2009

ml85
  • 67 Answers

SOURCE: the inside door handle won't open door from inside outside door works fine it's on drivers side 2006 ford fusion selv6

It sounds like the connecting rod popped out of its plastic connector. Pull the door panel off and check both ends of the rod. It must be unhooked at one end or the other.

Posted on Feb 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 altima s driver's side door wont open from inside or outside thought door was frozen shut so pulled handle hard to try and open now cant open door


You will need to take inside door panel loose which is a little hard with door shut but it can be done and probably replace door Handel if the Handel it's self is not broke it's most likely just a little plastic clip that holds the rod to the lock

Feb 03, 2015 | 2009 Nissan Altima

Tip

How to remove a front right door panel concorde sedan four door 96


How to remove a door panel, first u must open the door and unscrew the screw that is in the door handle then with a flat head screw driver unhook the plastic conectors to the cover of the handel becarfull not to pull to hard gently pull it as needed then pull the door handle as if opening and then pull the cover of handle out wards and then un detach the electric conector for the door locks then on the bottom handel unscrew the screw that is in the handle then pull out the case that holds it. then unscrew the screws that are on the inside towards the interior of the car there are two then two on the bottom then on the side that opens there should be on or two then pull the panel upwards and then towards your self you should be able to also detach the electric conector for the windows then when your done fixing it the instalation is reverse make sure that you conect the window and door lock conectores and make sure that the door falls in place with window latch. good luck buudy.

on Aug 22, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Jetta Volkswagen 1987 mercury door


TAKE PANNEL OFF IN SIDE AND SEE IF IT HAS A QUICK RELEASE OR IF THERE IS A BAR YOU CAN PULL OR PUSH TO RELEASE

Aug 12, 2012 | 1987 Volkswagen Jetta

1 Answer

2006 Chevy Impala drivers side rear door stuck from outside and inside. How do I remove door panel with door shut?


here is a picture of the door panel components:acceptwha619.gif
those numbered 2 and 4 are screws 7 and 8 are plastic fasteners that should just pull out the door frame with an a little force outward on the plastic door panel.

May 03, 2011 | 2006 Chevrolet Impala

1 Answer

How do you get the door panel off a 1988 Cadillac Fleetwood D'Elegence?


Disconnect negative battery terminal. Pull out inside door handel,then remove screws from behind it then pry out the door handel bezel.Pry upwards and out on the armrest switch control plate and disconnect electrical connections.Remove the door panel screws through the armrest opening .remove the screws from under the door pull handel as well.Pry out the interiory lamps mounted in the ends of the armrest and remove the panel screws from behind it. Also make sure there are no lamps hidden from view like under the armrest if so pry out lamp and remove panel screws from under it.Next start at the bottom of the door and trim panel and pry out each retaining clip. Clips are approximately 8 inches apart.Once all of the clips and screws are removed from the door panel it can be removed by gently lifting up and out on door panel.Ihope you find this helpfull,good luck.

Dec 06, 2010 | 1988 Cadillac Fleetwood

1 Answer

How to, removing front right door panel on 1996 concorde chrysler 4dr sedan


How to remove a door panel, first u must open the door and unscrew the screw that is in the door handle then with a flat head screw driver unhook the plastic conectors to the cover of the handel becarfull not to pull to hard gently pull it as needed then pull the door handle as if opening and then pull the cover of handle out wards and then un detach the electric conector for the door locks then on the bottom handel unscrew the screw that is in the handle then pull out the case that holds it. then unscrew the screws that are on the inside towards the interior of the car there are two then two on the bottom then on the side that opens there should be on or two then pull the panel upwards and then towards your self you should be able to also detach the electric conector for the windows then when your done fixing it the instalation is reverse make sure that you conect the window and door lock conectores and make sure that the door falls in place with window latch. good luck buudy.

Aug 16, 2010 | 1996 Chrysler Concorde

2 Answers

My back door will not shut, could it be the outside handle or something else


check to see if your latch is open unlock door put a screwdriver in the latch and open door with out side handel latsh will release

Dec 31, 2009 | 2000 Nissan Xterra

1 Answer

Tahoe passenger door won't open


remove vertical screws from arm rest. ther may be other screwscovered by plastic caps. pull small triangular cover at top near dash covering mirror mounting bolts. pop window and lock switches up and out of the door pannel and be carfull when removing electical connections from those switches. then pop plastic panel around inner door handel out and turn to free from handel. Now u can start to remove the door panel. U can by a special tool at your parts store to pop the clips on the inside of panel or just pull it off starting from the bottom and working yourwhay around the sides and up to the top. then push upwards from the bottlm and the top lip should pop free of the door.
hope this helps

Aug 09, 2009 | 1998 Chevrolet Tahoe

1 Answer

Something iside the door gave out outside handel doesnt work just


Follow the screws on the inside of the door. There will be several to find and then you can remove the inside door panel cover.

Jun 29, 2009 | 1998 Lexus ES 300

1 Answer

1998 Sienna Back Door Latch Stuck Open - Door will not open


well to get the door open you have to get the panel off first remove the assist grip and the pull strap ure ganna need a 10mm socket then pry around the panel and pull it off carefully watch for clips that may have fall off there should be 11 clips once you get the panel off you shoul be able to open the door. GOOD LUCK!! hope thats usefull

Jan 08, 2009 | 1998 Toyota Sienna

Not finding what you are looking for?
1995 Ford Thunderbird Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...