Question about 2007 Pontiac G6

1 Answer

Removal of engine cover

Remove engine cover

Posted by on

  • sydpfloyd
    sydpfloyd Jan 17, 2013

    ok found to twist oil filler tube 90 it removes thru cover, got it!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 937 Answers

Pry apart the back cover by guiding the flat-head screwdriver along the separating line between the front and back covers of the iPhone. When the back cover is apart from the front cover, flip the back cover off the iPhone, but be careful because a flat cable that goes to the motherboard connects the two covers.-----------------------------------------------------------------------------------
NEXIQ 125032 USB Link Plus

Posted on Jan 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changhing valve cover gasket 03 mitz galant 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the upper intake manifold.
  3. On the 3.0L DOHC engine, remove the ignition wire cover.
  4. Remove the ignition wires and spark plugs.
  5. Remove the crankcase ventilation tubes from both valve covers.
  6. Remove the retaining nuts and engine wiring from both valve covers and move aside.
  7. Remove the valve cover retaining bolts and studs.
  8. Remove both valve covers from the engine.
To install:
  1. Clean the valve cover gasket sealing surfaces.
  2. Install new valve cover gaskets onto the valve covers.
  3. Place the valve covers into position.
  4. Reinstall the valve cover retaining bolts and studs and tighten in sequence to:

    3.0L SOHC engine: 7 ft. lbs. (9 Nm)3.0L DOHC engine: 42-54 inch lbs. (4-5 Nm)3.5L engine: 30 inch lbs. (3 Nm)
  5. Install the engine wiring and tighten the retaining nuts.
  6. Install the crankcase ventilation tubes into both valve covers.
  7. Install the ignition wire separators, the ignition wires, and the spark plugs.
  8. On the 3.0L DOHC engine, install the ignition wire cover.
  9. Install the upper intake manifold as described in this section.
  10. Connect the negative battery cable.
  11. Run the engine and check for leaks and proper operation.

Jun 25, 2017 | Cars & Trucks

1 Answer

Where is the transmission temperature censer located on a 2003 Buick regal?


(391) Automatic Transmission Fluid Temperature (TFT) Sensor
Inside the transmission behind side cover
Removal Procedure
Remove the case side cover. Refer to Control Valve Body Cover Replacement .

Important: Lock steering wheel in centered position with wheels straight ahead.
Remove the engine dress cover.
Remove the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.1L or Air Cleaner Inlet Duct Replacement in Engine Controls - 3.8L.
Remove the engine mount struts. Refer to Engine Mount Strut Replacement in Engine Mechanical - 3.1L or Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side in Engine Mechanical - 3.8L.
Important: For supercharged engines, remove the throttle cable bracket.
Disconnect the shift cable bracket.
Remove the transaxle top side cover bolt.
Install the engine support fixture. Refer to Engine Support Fixture in Engine Mechanical - 3.1L or Engine Support Fixture in Engine Mechanical - 3.8L.
Disconnect the transmission wiring harness connector.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
Remove the left front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
Remove the left inner splash shield 3 push pins.
Loosen the wheel speed sensor harness from the 5 retainers at the cradle.
Remove the transmission support to cradle nuts only. Refer to Transmission Mount Replacement .
Raise the vehicle.
Remove the front splash shield 5 bolts.
Loosen the engine mount lower nuts. Refer to Engine Mount Bracket Replacement in Engine Mechanical - 3.1L or Engine Mount and Bracket Replacement in Engine Mechanical - 3.8L.
Remove the stabilizer bolts and reposition the stabilizer.
Remove the steering gear cradle bolts, then support gear before lowering cradle.
Support the left side of the frame with a jackstand.
Remove the left side frame bolts. DO NOT loosen the right front or the right rear frame bolts. Refer to Frame Replacement in Frame and Underbody.
Remove the left ball joint from the steering knuckle.
Position the drain pan under the transaxle.
Remove the left drive axle from the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
Secure the drive axle to the steering knuckle/strut.
Adjust the jackstand to lower the left side of the frame until it hangs free. Remove jack stand.
Lower vehicle to access engine support fixture.
Lower the engine/transmission assembly with the engine support fixture to gain access to remaining side cover bolts.
If replacing the side cover, remove 4 engine mount bracket bolts.
Remove the harness retainer.
Raise vehicle to access side cover bolts.
Remove the case side cover bolts (56-58).
Remove the case side cover pan (53).
Remove the case side cover gasket (54).
Clean the case.
Clean the side cover gasket mating surfaces.

Disconnect the wiring harness assembly from the fluid temperature sensor (391).
Remove the fluid temperature sensor (391).
Installation Procedure
Install the fluid temperature sensor (391).
Connect the wiring harness assembly to the with fluid temperature sensor (391).
Install the case side cover. Refer to Control Valve Body Cover Replacement .
Important: It is recommended that transmission adaptive pressure (TAP) information be reset. Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.
Reset the TAP values. Refer to Transmission Adaptive Functions .

Nov 23, 2016 | Buick Cars & Trucks

1 Answer

Front seal replacement 5.9 cummins


Hi Dale, I'm glad to help! Below is the removal procedure for the front crankshaft seal on your 5.9 cummins engine. Hope this helps and have an awesome day!



REMOVAL

  1. Disconnect both battery negative cables.
  2. Raise vehicle on hoist.
  3. Partially drain engine coolant into container suitable for re-use (Refer to 7 - COOLING - STANDARD PROCEDURE).
  4. Lower vehicle.
  5. Remove radiator upper hose.
  6. Disconnect coolant recovery bottle from radiator filler neck and lift bottle off of fan shroud.
  7. Disconnect windshield washer pump supply hose and electrical connections and lift washer bottle off of fan shroud.
  8. Remove viscous fan/drive assembly. (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
  9. Remove cooling fan shroud and fan assembly from the vehicle.
  10. Remove the accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - REMOVAL).
  11. Remove the cooling fan support/hub from the front of the engine.
  12. Raise the vehicle on hoist.
  13. Remove the crankshaft damper and speed indicator ring.
  14. Remove power steering pump.
  15. Remove accessory drive belt tensioner.
  16. Remove the gear cover-to-housing bolts and gently pry the cover away from the housing, taking care not to mar the gasket surfaces. Remove crank seal dust shield with cover.
  17. Support the cover on a flat work surface with wooden blocks (Removing Seal from Cover), and using a suitable punch and hammer, drive the old seal out of the cover from the back side of the cover to the front side(Removing Seal from Cover).

Apr 10, 2014 | 2004 Dodge Ram 2500

1 Answer

Change timing belt


timing belt? on a Jeep? 05 wrangler
what engine is this>?
ah the 2.4L
front cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the crankshaft vibration damper.
  3. Remove the generator drive belt tensioner assembly.
  4. Remove the timing belt front cover bolts, and remove the covers.


rear cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the front covers.
  3. Remove the timing belt.
  4. Hold the camshaft sprocket with Special Tool 6847, or equivalent, while removing the center bolt.
  5. Remove the timing belt idler pulley.
  6. Remove the rear cover fasteners and remove the cover from engine.

Apr 04, 2014 | 2005 Jeep Wrangler

1 Answer

Re-sealing timing belt cover 2007 Camry


wow no engine stated, post engine size.
depends if mechanic is size of squirrel or a gorilla.
huh?
why not longin to alldata. com and read the page on timing belt changeout.
you can goggle this, 1000s of hits, why not ?

there are serious costs to do service on most FWD cars.
next time buy a RWD car. far easier to fix.
FWD is cheaper to make, (pull rad, fix, put back Rad)
there are 3 engines. ill roll the dice, and log in to alldata.
and see. 37steps out and 37 steps in,
about
not one word, TO pull engine, 2AZ-FE CHAIN
THE 2GR-fe ENGINE IS CHAIN TO.
see step 29, your posted ITEM>!!
PASTED, 2gr CAM BELT SECTIONS;
  • 2007 TOYOTA Camry HV

1. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
4. REMOVE FRONT WHEEL RH
5. REMOVE ENGINE UNDER COVER LH
6. REMOVE ENGINE UNDER COVER RH
7. REMOVE FRONT FENDER APRON SEAL RH
8. DRAIN ENGINE OIL


10. REMOVE NO. 2 ENGINE MOUNTING STAY RH
11. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY
12. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH
13. REMOVE V-RIBBED BELT TENSIONER COVER SUB-ASSEMBLY
21. SET NO. 1 CYLINDER TO TDC/COMPRESSION
22. REMOVE CRANKSHAFT PULLEY
23. REMOVE CRANK POSITION SENSOR
24. REMOVE OIL PAN SUB-ASSEMBLY
Remove the 12 bolts and 2 nuts.
Insert the blade of SST between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

25. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Remove the 2 nuts, tensioner and gasket.

Do not turn the crankshaft without the chain tensioner.
26. INSTALL ENGINE HANGERS
Install the No. 1 engine hanger and No. 2 engine hanger with the bolts as shown in the illustration.
  • Attach the sling device to the engine hangers and chain block.
27. REMOVE ENGINE MOUNTING INSULATOR
Attach the engine chain hoist to the engine hangers.
  • Do not attempt to hang the engine by hooking the chain to any other part.
  • Remove the bolt and disconnect the engine mounting insulator FR.
  • Remove the 4 nuts from the engine mounting insulator RH.

  • Raise the engine and remove the engine mounting insulator RH.
28. REMOVE ENGINE MOUNTING BRACKET RH
Remove the 3 bolts and engine mounting bracket RH.
29. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
30. REMOVE TIMING CHAIN CASE OIL SEAL
31. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Remove the crankshaft position sensor plate.
AND SO ON,,,, end. quote.

AS YOU CAN SEE ITS NOT A MOTOR PULL BUT IS UNMOUNTED
AND FLOATED,

Now begs the question, which is less work. the above, or just pull the engine, and work sitting down. easy work and higher quality
may that depends on the person and his/her size.

Jan 08, 2014 | Toyota Camry Cars & Trucks

1 Answer

Check an ignition coil pack for aura 3.2 TL






ironfist109_390.jpg




  • For coil wires.

  1. Remove the intake cover.
  2. Remove the right side engine cover - A -
  3. Remove the left engine cover - B -
  4. Remove Right rear engine cover - C -
  5. To remove the #6 coil you will also need to remoce the heat shiel off th reserve tank and the reserve tank as well.


  • For coil pack.

  1. Remove negative battery cable
  2. Remove engine covers show in diagram.
  3. Remove the coils (listed above).
  4. Now just remove the mounting bolts to the coil packs.

  • Please Note - Don't loose the firing order of your car will not run.

  • Here is a spare one in case you get mixed up.
  • Firing order is
  • 1-4-2-5-3-6



ironfist109_391.jpg



  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 13, 2011 | 2002 Acura 3.2TL

1 Answer

Do you need to remove oil pan to remove timing chain cover on a 2000 Cavalier 2.2?


no, here is the procedure. Please let me know if you have more questions.

REMOVAL & INSTALLATION

2.2L Engine
  1. Remove the serpentine belt and tensioner.

Although not absolutely necessary, removal of the right front inner fender splash shield will facilitate access to the front cover.
  1. Install a suitable engine support fixture.
  2. Remove the engine mount assembly.
  3. Remove the alternator rear brace, then remove the alternator.
  4. Remove the power steering pump, then position it aside with the lines still attached.
  5. Raise and safely support the vehicle.
  6. Remove the front two oil pan bolts.
  7. Remove the crankshaft pulley.
  8. Unfasten the front cover-to-block bolts and then remove the front cover. If the front cover is difficult to remove, use a plastic mallet to carefully loosen the cover.

Aug 27, 2011 | 2000 Chevrolet Cavalier

1 Answer

Finding the starter on 2005 nissan pathfinder


STARTER LOCATION ON 4.0 V6 -REMOVE ENGINE UNDER COVER.REMOVE EXHAUST MANIFOLD COVER FROM EXHAUST MANIFOLD RIGHT BANK TO GAIN ACCESS TO STARTER COVER BOLTS.THEN REMOVE STARTER COVER BOLTS AND REMOVE STARTER COVER.**** 5.6 V8 ENGINE YOU HAVE TO REMOVE INTAKE MANIFOLD TO GET TO THE STARTER.

Sep 10, 2010 | 2005 Nissan Pathfinder

1 Answer

Need to remove external oil pump on a 95 ford tauras 3.8 v6.what all is involved doing this??


Oil Pump

Removal


  1. If necessary, remove oil bypass filter (oil filter).
  2. Remove oil pump and filter body to engine front cover retaining bolts and remove oil pump and filter body from engine front cover.
  3. Inspect oil pump body seal (6C639), oil pump and filter body and engine front cover for distortion and wear. Replace components as necessary.
Installation

  1. Position oil pump and filter body on engine front cover and install retaining bolts.
  2. Tighten the small engine front cover retaining bolts to 8-11 Nm (71-97 lb-in) . Tighten the large retaining bolts to 23-32 Nm (17-23 lb-in) .
  3. If removed, reinstall oil bypass filter (oil filter).

Dec 04, 2009 | 1995 Ford Taurus

1 Answer

Changing valve cover gasket


v6 or 4 cylinder?

SECTION 303-01A: Engine - 2.0L 1999 Cougar Workshop Manual
IN-VEHICLE REPAIR Valve Cover Removal
  1. Disconnect the oil feed sensor electrical connector.
  1. Disconnect the crankcase ventilation tube.
  1. Remove the appearance cover.
    1. Position the throttle cable out of the way, and the speed control cable (if equipped).
    1. Remove the eight bolts.
    1. Remove the appearance cover.
  1. Remove the spark plug wires.
  1. Detach the upper part of the engine front cover out of the way.
    1. Remove the four bolts.
    1. Position the front cover to one side.
  1. Remove the valve cover.
    1. Position the throttle cable to one side, and the speed control cable (if equipped).
    1. Remove the nine bolts.
    1. Remove the valve cover
---------------------------------------------------------------------------------------------

Mar 23, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
2007 Pontiac G6 Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...